manualshive.com logo in svg

Cypress EZ-USB CX3, Техническое справочное руководство, Страница: 28 / 35

Поделиться
Скачать
Cypress EZ-USB CX3 Скачать руководство пользователя страница 28

 

Cypress EZ-USB CX3  

EZ-USB® CX3 Technical Reference Manual, Doc. No. 001-91492 Rev. *B 

28 

1.11   CX3 MIPI CSI-2 APIs 

This section details the APIs exposed by the 

EZ USB FX3 SDK 

to configure and utilize the MIPI CSI-2 block 

on the CX3. Additional details on the APIs and the enumerations and structure types used by them can be 
found in the EZ-USB FX3/FX3S/CX3 SDK Firmware API Guide available as part of the 

EZ USB FX3 SDK

.  

The MIPI CSI-2 block configuration APIs are available through the cyu3mipicsi.a library file and the function 
declarations, enumerations and structure types are available through the header file 

cyu3mipicsi.h

. 

EZ USB FX3 SDK

 1.3 provided a BETA level support for the CX3 part. Full support for the CX3 part is available 

as part of the 

EZ-USB FX3 SDK

 starting from the 

EZ-USB FX3 SDK

 1.3.1 release. 

1.11.1   

CyU3PMipicsiInit() 

 

CyU3PReturnStatus_t CyU3PMipicsiInit (void) 

This function initializes MIPI CSI-2 block on the CX3 device and is expected to be called prior to any other 
calls  to  the  MIPI  CSI-2  block.  The  CX3  GPIO  Block,  the  PIB  block  and  the  I

2

C  blocks  should  have  been 

initialized prior to calling this function.  

This call leaves the MIPI CSI-2 block in a low-power mode and 

CyU3PMipicsiWakeup()

 

should be called to 

enable the clocks on the MIPI CSI-2 block.  

This function internally power cycles the MIPI CSI-2 block.  

It  also  enables  the  output  of  XRESET  and  XSHUTDOWN  signals  by  setting 

XSHUTDOWN  ENABLE

  and 

XRESET ENABLE

 bits of the 

CX3_CSI_SENSOR_SIG_EN 

register to 0.  

This function leaves the 

CX3_CSI_SENSOR_SIG_VAL 

register in its default state (0x0000) thereby setting 

the MIPI XRESET and XSHUTDOWN signals to Drive LOW. If either of these signals, needs to be in Drive 
HIGH  state  for  sensor  operation,  it  needs  to  be  explicitly  set  to  Drive  HIGH  state  using 

CyU3PMipicsiSetSensorControl()

 

API after calling this function.  

On successful execution this function returns CY_U3P_SUCCESS value to the calling function. 

1.11.2   

CyU3PMipicsiDeInit() 

 

CyU3PReturnStatus_t CyU3PMipicsiDeInit (void) 

This function de-initializes MIPI-CSI interface block on the CX3 device and is expected to be called prior to 
calling 

CyU3PSysEnterStandbyMode()

. This function should be called before the I

2

C block or GPIO blocks 

are de-initialized.  

The MIPI XRESET and XSHUTDOWN signals shall not be driven by the CX3 after this call. 

On successful execution this function returns CY_U3P_SUCCESS value to the calling function. 

1.11.3   

CyU3PMipicsiReset() 

 

CyU3PReturnStatus_t CyU3PMipicsiReset (CyU3PMipicsiReset_t resetType) 

This function is used to reset the MIPI-CSI block on the CX3. The MIPI-CSI block provides two reset modes 
– 

Hard  reset

,  which  power-cycles  the  entire  block,  and 

Soft  reset

,  which  does  not  reset  the  I

2

C 

communication  channel  used  by  the  block.  The  reset  mode  is  selected  via  the  parameter  of  type 

CyU3PMipicsiReset_t

 passed to this function. 

Soft Reset cannot be called on the interface until the block has been initialized. A Hard reset however, can be 
called on the interface at any point in time.  

The 

CyU3PMipicsiInit()

 call internally performs a Hard reset on the interface before initializing it.  

Hard reset enables the output of XRESET and XSHUTDOWN signals by setting 

XSHUTDOWN ENABLE

 and 

XRESET  ENABLE

  bits  of  the 

CX3_CSI_SENSOR_SIG_EN

 

register  to  0.  This  function  leaves  the 

Содержание EZ-USB CX3




































Отзывы:

Нет отзывов