Cypress EZ-USB CX3 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 35

Cypress EZ-USB CX3 Скачать руководство пользователя страница 13

Cypress EZ-USB CX3

EZ-USB® CX3 Technical Reference Manual, Doc. No. 001-91492 Rev. *B

13

1.8 CX3 MIPI CSI-2 Block Power Modes

The MIPI CSI-2 block on CX3 supports the following power modes:

▪

Active

: In this mode, the MIPI CSI-2 receiver block will be active and transfer data from the image

sensor to the GPIF II interface.

▪

Low-Power Sleep

: In this mode, all data transfer clocks on the MIPI CSI-2 block are stopped and there

will be no data transfer. All register settings are retained in this state.

▪

Soft Reset

: This state puts the MIPI CSI-2 block into reset mode where all clocks on the interface are

stopped. The MIPI CSI-2 block configuration register states are retained across a soft reset.

▪

Hard Reset

: In this state the MIPI CSI-2 controller and all clocks are stopped. The MIPI CSI-2 block

configuration registers are reset to their default states by a hard reset. Hard reset is automatically
executed during MIPI CSI-2 receiver initialization.

«
...
11
12
13
14
15
...
»

Содержание EZ-USB CX3




































Отзывы:

Нет отзывов