Cypress EZ-USB CX3 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 35

Cypress EZ-USB CX3 Скачать руководство пользователя страница 10

Cypress EZ-USB CX3

EZ-USB® CX3 Technical Reference Manual, Doc. No. 001-91492 Rev. *B

10

Format and

Mode

CX3 Firmware Stream Format

Name

Format

Description,

Pixel Depth

CSI-2

Data

Typea

GPIF II
Bus Width

Output Stream

YUV422

8-bit Mode 1

CY_U3P_CSI_DF_YUV422_8_1

YUV422 format
16 bits per
pixel

0x1E

16-bit

P[15:0]
Data Order:
{U1,Y1},{V1,Y2},{
U3, Y3},{V3,Y4}...

YUV422
8-bit Mode 2

CY_U3P_CSI_DF_YUV422_8_2

YUV422 format
16 bits per
pixel

0x1E

16-bit

P[15:0]

Data Order:
{Y1,U1},{Y2,V1},{
Y3,
U3},{Y4,V3}....

YUV422
10-bit

CY_U3P_CSI_DF_YUV422_10

YUV422 format
20 bits per
pixel

0x1F

16-bit

6'b0,P[9:0]
Data Order:
U1,Y1,V1,Y2,U3,
Y3, V3,Y4.

a

MIPI CSI-2 defined Data Type code. Please refer to the MIPI CSI-2 specification for details.

If the GPIF II bus width selected is larger than the width of the output stream, for example if a 24-bit GPIF II
bus width is used for the CY_U3P_CSI_DF_YUV422_8_1 type, the upper bits on the GPIF II are padded with
0s.

For stream formats not listed in

, such as MJPEG or custom format streams, 8 bit wide streams can

be transported on the RAW8 stream format, and 24 bit wide streams can be transported by treating the stream
as an RGB888 format stream. GPIF bus widths and buffers should be set up appropriately to match the stream
output. Section

has more details on setting up the GPIF bus-width and DMA buffers.

Packing more than one pixel per PCLK is possible. For example, selecting the

“MIPI CSI input -Data format"

configured as "RAW8" and the

“MIPI interface configuration – data format” as a 24bit format (RGB888) will

output three pixel data per PCLK. Similarly, two 10 bit or 12bit pixels can be packed and output per PCLK
using the 24 bit output format.

«
...
8
9
10
11
12
...
»

Содержание EZ-USB CX3




































Отзывы:

Нет отзывов