manualshive.com logo in svg

Cypress enCoRe V CY7C643 Series, Техническое справочное руководство

Поделиться
Скачать
Cypress enCoRe V CY7C643 Series Скачать руководство пользователя страница 128

enCoRe™ V CY7C643xx, enCoRe™ V LV CY7C604xx TRM, Document No. 001-32519 Rev *H

128

SPI

Configuration Register 

The configuration block contains 1 register. This register must not be changed while the block is enabled. Note that the SPI
Configuration register is located in bank 1 of the enCoRe V device’s memory map.

18.2.4

SPI_CFG Register

The SPI Configuration Register (SPI_CFG) is used to con-
figure the SPI.

Bits 7 to 5: Clock Sel [2:0].  

Clock  Selection.  These  bits

determine the operating frequency of the SPI Master.

Bit 4: Bypass.  

This  bit  determines  whether  the  inputs  are

synchronized to SYSCLK.

Bit 3: SS_.  

Slave  Select.  This  bit  determines  the  logic

value of the SS_ signal when the SS_EN_ signal is asserted
(SS_EN_ = 0).

Bit 2: SS_EN_.  

Slave  Select  Enable.  This  active  low  bit

determines  if  the  slave  select  (SS_)  signal  is  driven  inter-
nally. If it is driven internally, its logic level is determined by
the SS_ bit. If it is driven externally, its logic level is deter-
mined by the external pin.

Bit 1: Int Sel.  

Interrupt Select. This bit selects which condi-

tion produces an interrupt.

Bit 0: Slave.  

This  bit  determines  whether  the  block  func-

tions as a master or slave.

For additional information, refer to the 

SPI_CFG register on

page 214

.

18.2.4.1

SPI Configuration Register Definitions

18.2.5

Related Registers

■

IO_CFG1 Register on page 224.

Address

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Access

1,29h

SPI_CFG

Clock Sel[2:0]

Bypass

SS_

SS_EN_

Int Sel

Slave

RW : 00

Table 18-5.  SPI Configuration Register Descriptions

Bit #

Name

Access

Mode

Description

7:5

Clock Sel

Read/Write

Master

SYSCLK
000b / 2
001b / 4
010b / 8
011b

/ 16

100b / 32
101b / 64
110b

/ 128

111b

/ 256

4

Bypass

Read/Write

Master/Slave

0 = All pin inputs are doubled, synchronized.
1 = Input synchronization is bypassed.

3

SS_

Read/Write

Slave

0 = Slave selected.
1 = Slave not selected. Slave selection is determined from external SS_ pin.

2

SS_EN_

Read/Write

Slave

0 = Slave selection determined from SS_ bit.
1 = Slave selection determined from external SS_ pin.

1

Int Sel

Read/Write

Master/Slave

0 = Interrupt on TX Reg Empty.
1 = Interrupt on SPI Complete.

0

Slave

Read/Write

Master/Slave

0 = Operates as a master.
1 = Operates as a slave.

Содержание enCoRe V CY7C643 Series


































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды