Cypress CY8C28 series Скачать руководство пользователя

Страница: 199 / 571

I2Cx_MSCR

198

CY8C28xxx PSoC Programmable System-on-Chip TRM, Document No. 001-52594 Rev. *G

0,D9h

13.2.66

I2Cx_MSCR

C Master Status and Control Register

This register implements I

C framing controls and provides Bus Busy status. Note that the second I

C block is available in the

CY8C28x03, CY8C28x23, CY8C28x43, and CY8C28x45 PSoC devices only.

Bits in this register are held in reset until one of the enable bits in I2C_CFG is set.

In the table, note that reserved bits are

grayed table cells and are not described in the bit description section. Reserved bits should always be written with a value of

‘0’. For additional information, refer to the

“Register Definitions” on page 497

in the I

C chapter

Bus Busy

This bit is set to the following.
0

When a Stop condition is detected (from any bus master).

When a Start condition is detected (from any bus master).

Master Mode

This bit is set/cleared by hardware when the device is operating as a master.
0

Stop condition detected, generated by this device.

Start condition detected, generated by this device.

Restart Gen

This bit is cleared by hardware when the Restart generation is complete.
0

Restart generation complete.

Generate a Restart condition.

Start Gen

This bit is cleared by hardware when the Start generation is complete.
0

Start generation complete.

Generate a Start condition and send a byte (address) to the I

C bus, if bus is not busy.

Individual Register Names and Addresses:

0,D9h

I2C0_MSCR

: 0,D9h

I2C1_MSCR : 0,E5h

Access : POR

R : 0

RW : 0

Bit Name

Bus Busy

Master Mode

Restart Gen

Start Gen

Bit

Name

Description

Содержание CY8C28 series




























































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CY8C28 series

Отзывы:

Похожие инструкции для CY8C28 series

Бренды по названию

Популярные бренды

Cypress CY8C28 series, Техническое справочное руководство

Результаты поиска

Содержание CY8C28 series

Отзывы:

Похожие инструкции для CY8C28 series

Бренды по названию

Популярные бренды