10-Outlet Surge Protector
CSP1008T
CONGRATULATIONS ON YOUR PURCHASE
Thank you for selecting the CyberPower CSP1008T Surge
Protector. The information contained in this brochure explains the
features and operation of the CSP1008T. Please take a few
moments to read this manual.
FEATURES
1. ON/OFF Reset Control Switch and Circuit Breaker
Controls power to all outlets. The switch is also a 15A breaker.
When an overload occurs, it will automatically switch off. To
resume operation, ensure the overload condition is removed and
reset the surge protector by switching the unit ON.
2. Grounded LED Indicator
Illuminated when a properly grounded AC outlet is detected.
3. Protected LED Indicator
Illuminated when the surge protection feature is working properly.
4. Surge Protected Data Line Connections
To protect your equipment from surge along phones/fax/
modems lines.
A. Connect the phone line from wall outlet into the “In” port.
B. Connect the phones/fax/modems line(s) in the “Out” ports.
5. Safety Covers
All outlets on this surge protector include safety covers. To
ensure the safety of children and to avoid electric shock and
damage from a high-dust environment, slide the plastic outlet
cover over outlets that are not used.
6. Two Wide-Spaced Outlets
Easily plug in large chargers without interfering with the
other outlets.
7. Cord Gathering Bracket
Keeps power cords neat and organized.
SPECIFICATIONS
•
Model Number:
CSP1008T
•
Outlets:
10 – 2 Transformer Spaced Outlets
•
Surge Protection:
2850 Joules
•
Electrical Rating:
125V/15A/1875W
•
UL Clamping Voltage:
UL 1449 3
rd
/400V (H-N, H-G, N-G)
•
Maximum Peak Current:
135,000A
•
3 AC Lines Protected:
H-N: 75,000A, H-G: 30,000A,
N-G: 30,000A;(The maximum surge possible on household
wiring is 6,000 volts)
•
Response Time:
Less than 1 nanosecond
•
Attenuation:
Up to 43dB
•
Telecommunications Protection:
RJ11 1 in / 2 out
•
Circuit Breaker:
Resettable 15 Amp
•
EMI/RFI Filtration:
150 kHz to 100 MHz
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK
- Use only in dry
locations and only indoors.
DO NOT
plug into another relocat-
able power tap.
DO NOT
“daisy chain” surge protectors.
DO NOT
use with any aquarium equipment.
DO NOT
use if
properly grounded outlets are not available.
DO NOT
install this
device if there is not at least 10 meters (30 feet) or more of wire
between the electrical outlet and electrical service panel. This
device features an internal protection that will disconnect the
surge protective component at the end of its useful life, but will
maintain power to the load – now unprotected.
TROUBLESHOOTING
If the
ON/OFF
is switched off, the 15 AMP circuit breaker may
have tripped. Examine your connected equipment and remove
the device that is overloading the circuit. Then, the
ON/OFF
switch back to
RESET
.
If the
Grounded
indicator does not light when you plug in the
surge protector, move the surge protector to a different
grounded three-prong AC outlet. If it still does not light, return
the product to the dealer for assistance. If the surge protector
proves to be working properly, your outlets may not be properly
grounded and need to be repaired by a professional electrician.
If the
Grounded
indicator turns off after a period of use, the
surge protection has been depleted. Replace your
surge protector.
If the
Protected
indicator does not light, the surge protector’s
AC line is no longer protected from surges. Replace the surge
protector. The surge protector may have received a power
surge or spike beyond its specified limits that might overload
the protection circuitry and make it inactive. The surge
protector absorbed enough of the surge to protect your
connected equipment, but it will not protect against future
surges and spikes.
TECHNICAL SUPPORT
Please contact our Tech Support department with installation,
troubleshooting, or general product questions.
•
Phone:
1-877-297-6937
•
Email:
•
Hours of Operation:
Monday – Friday, 8:00am – 5:00pm CST
© 2012 CyberPower Systems, Inc.
All rights reserved. All other trademarks are the property of their
respective owners.
K09-0000113-00
User Manual
LIMITED WARRANTY AND CONNECTED
EQUIPMENT GUARANTEE
Read the following terms and conditions carefully before using
the CyberPower CSP1008T (the “CPS Product”). By using the
CPS Product, you consent to be bound by the terms and
conditions of this Limited Warranty and Connected Equipment
Guarantee (together referred to as this “Warranty”). IF YOU DO
NOT AGREE TO THE TERMS AND CONDITIONS OF THIS
WARRANTY, YOU SHOULD RETURN THE PRODUCT FOR A
FULL REFUND PRIOR TO USING IT.
Who is providing this Warranty, what does it cover?
CyberPower Systems (USA), Inc. (“CyberPower”) provides this
Limited Warranty. It only covers the original purchaser and ends
if you no longer own the CPS Product. This warranty covers
defects in materials and workmanship in the CPS Product under
normal use and conditions. It also covers equipment connected
to the CPS Product and damaged because of the failure of the
CPS Product. This warranty covers the CPS Product and
connected equipment for as long as you own the CPS Product.
What must I do to make a warranty claim?
1. Call (877) 297-6937 or write to CyberPower, 4241 12th Ave.
E., STE 400, Shakopee, MN 55379 or send a message at
[email protected] for instructions.
2. Identify the Product, the Purchase Date, and the item(s) of
Connected Equipment.
3. Provide a dated Proof-of-Purchase receipt (or other proof of
the original purchase) and provide a description of the defect.
4. Pack and ship the product to CyberPower and, if requested,
the item(s) of Connected Equipment, and all claim forms that
CyberPower provides to you. Show the Claim Number on the
shipping label or include it with the product.
You must prepay
all shipping costs, you are responsible for packaging and
shipment, and you must pay the cost of the repair estimate.
5. Do each of these within ten days of the occurrence.
What will CyberPower do to correct problems?
CyberPower will inspect and examine the CPS Product. If the
CPS Product is defective in material or workmanship,
CyberPower will repair or replace it at CyberPower’s expense, or
CyberPower will refund the full purchase price you paid for the
CPS Product (purchase receipt showing price paid is required).
If the CPS Product failed to protect any equipment plugged into
it, we will also send you forms for making your claim for the
connected equipment. We will repair or replace the equipment
that was damaged because of the failure of the CPS Product or
pay you the
fair market value (NOT REPLACEMENT COST)
of
the equipment at of the time of the damage. We will use Orion
Blue Book, another a third-party valuation guide, eBay, craigslist,
or other source to establish that amount. Our maximum liability is
limited to $400,000 for the CSP1008T.
Who pays for shipping?
We pay when we send items to you; you pay when you send items
to us.
What are some things this Warranty does not cover?
1. THIS WARRANTY DOES NOT COVER ANY SOFTWARE THAT
WAS DAMAGED OR NEEDS TO BE REPLACED DUE TO THE
FAILURE OF THE CPS PRODUCT OR ANY DATA THAT IS
LOST AS A RESULT OF THE FAILURE OR THE
RESTORATION OF DATA OR RECORDS, OR THE REINSTAL-
LATION OF SOFTWARE.
2. This Warranty does not cover: misuse, modification, operation
or storage outside environmental limits of the CPS Product or
the equipment connected to it, or for damage while in transit or
in storage, nor if there has been improper operation or
maintenance, or use with items not designed or intended for
use with the CPS Product, such as laser printers, appliances,
aquariums, medical or life support devices, etc.
What are the other limitations?
The sole and exclusive remedies of the Initial Customer are those
provided by this Warranty.
1. This Warranty does not apply unless the CPS Product and the
connected equipment were connected to properly wired and
grounded outlets (including compliance with electrical and
safety codes of the most current electrical code), without the
use of any adapters or other connectors.
2. The CPS Product must have been plugged directly into the
power source and the equipment connected to the CPS
Product must be directly connected in the CPS Product, not
“daisy-chained” together in serial fashion with any extension
cords, another Product or device similar to the CPS Product,
surge suppressor, or power tap. Any such installation voids
the Warranty.
3. The CPS Product and connected equipment must have been
used properly in a suitable and proper environment, in
conformance with any applicable license, instruction manual,
or warnings.
4. The CPS Product must have been used at all times within the
limitations on the CPS Product’s VA capacity.
Where can I get more information?
Contact CyberPower at 4241 12th Ave E., STE 400, Shakopee,
MN 55379; call us at (877) 297-6937; or send us an e-mail
message at [email protected].
PRODUCT REGISTRATION
Prompt product registration assures coverage under the Limited
Warranty, and also allows the opportunity to be notified of
product enhancements, upgrades, and other announcements.
Registration is quick and easy at www.cpsww.com/register.
CONTACT INFORMATION
CyberPower Systems, Inc.
4241 12th Avenue East Suite 400 Shakopee, MN 55379
Toll-free: 1-877-297-6937 | CPSww.com
This devise is manufactured using environmentally-safe
procedures in compliance with the Restriction on
Hazardous Substances (RoHS) directive.
Please join CyberPower in caring for the
environment by recycling this manual.
5
6
7
1
2
3
4
