manualshive.com logo in svg

CyberData RAL 9003, Руководство по эксплуатации, Страница: 76 / 126

Поделиться
Скачать
CyberData RAL 9003 Скачать руководство пользователя страница 76

 

Installing the Singlewire InformaCast Talk-Back Speaker

Device Configuration

Operations Guide

931260A

CyberData Corporation

69

Note

You must click on the 

Save

 button and then the 

Reboot

 button for the changes to take 

effect.

2.3.8.1 Assigning Priority

The device will prioritize simultaneous audio streams according to their priority in the list.

If both SIP and Multicast is enabled, SIP audio streams are considered priority 

4.5

. SIP audio will 

interrupt multicast streams with priority 

0

 through 

4

 and will be interrupted by multicast streams with 

priority 

5

 through 

9

.

During priority 

9

 multicast streams, the volume is set to maximum.

Note

SIP calls, multicast streams, ring tones, ringback tones, and nightring tones are all 
prioritized.

Ringtones and 
Nightringtones

Ringtones all play at the same priority level. This means that it is possible to have a nightring tone 
and a normal ringtone playing at the same time.

Fast Fade 

Strobe will increase in brightness from 0 to the specified 
brightness and back to 0 over the course of about 1.5 
seconds during the duration of the event.

Slow Blink 

Strobe will blink ON at the specified brightness for one 
second then OFF for one second during the duration of the 
event.

Fast Blink 

Strobe will blink ON at the specified brightness then OFF 
five times per second during the duration of the event.

Multicast Call Color 

Select desired color (only one may be chosen).

Red 

The red LED value for Multicast.

Green 

The green LED value for Multicast.

Blue 

The blue LED value for Multicast.

Use this button to preview the strobe flashing behavior for 
the 

Multicast Strobe Settings

.

Click the 

Save

 button to save your configuration settings.

Note

: You need to reboot for changes to take effect.

Click on the 

Reboot

 button to reboot the system.

Table 2-16. Multicast Configuration Parameters (continued)

Web Page Item

Description

Содержание RAL 9003































































































































Отзывы:

Нет отзывов