CyberData RAL 9003 Скачать руководство пользователя | Manualshive

Страница: 38 / 126

background image

Installing the Singlewire InformaCast Talk-Back Speaker

Device Configuration

Operations Guide

931260A

CyberData Corporation

31

2.2.3 Confirm that the Speaker is Operational and Linked to the Network

After connecting the speaker to the 802.3af compliant Ethernet hub, the LEDs on the speaker face
confirm that the speaker is operational and linked to the network.

Figure 2-9. Status and Activity LEDs

2.2.3.1 Status LED

After supplying power to the speaker:

1. The green power/status LED and the yellow network LED comes on immediately.

2. After about 23 seconds with a static IP address (or 27 seconds if the board is set to use DHCP),

the green LED will blink twice to indicate that the board is fully booted. The speaker will beep at
this time if the

Beep on Init

option is enabled on the

Device Configuration Page

(see

2.3.5, "Configure the Device"

).

Note

If the board is set to use DHCP and there is not a DHCP server available on the network, it
will try 12 times with a three second delay between tries and eventually fall back to the
programmed static IP address (by default 10.10.10.10). This process will take approximately
80 seconds.

Note

The front power/status LED will remain solid on during operation.

2.2.3.2 Link LED

•

The

Link

LED is illuminated when the network link to the speaker is established.

•

The

Link

LED blinks to indicate network traffic.

Speaker



Status



(Green)

Network



Link/Activity



(Yellow)

«
...
36
37
38
39
40
...
»

Содержание RAL 9003































































































































Отзывы:

Нет отзывов

Похожие инструкции для RAL 9003

Бренд: HIMA Страницы: 58

Бренд: EAW Страницы: 2

Бренд: Sandstrom Страницы: 32

ARK COLUMN Series

Бренд: DAD Страницы: 56

Sportsound SSR-300

Бренд: Daktronics Страницы: 6

WAGO-I/O-SYSTEM 750-424

Бренд: WAGO Страницы: 12

Бренд: Vidos Страницы: 8

4.3" Video Door Phone

Бренд: Alarmtec Страницы: 14

Бренд: Fender Страницы: 51

Бренд: Teac Страницы: 16

Бренд: Aiwa Страницы: 7

ENHANCE ATTACK ENPCSM2100BKUS

Бренд: Accessory Power Страницы: 16

Бренд: Balluff Страницы: 42

Бренд: urmet domus Страницы: 32

Бренд: Tokai Страницы: 42

Бренд: Bang & Olufsen Страницы: 34

Бренд: Topp Music Gear Страницы: 6

Бренд: Armstrong Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды