© 2020, CyberData Corporation, ALL RIGHTS RESERVED
931350C
Quick Reference
Quick Reference
931350C
© 2020, CyberData Corporation, ALL RIGHTS RESERVED
Install the DX70 Phone to Enclosure
Use a Paper Clip Through Hole
HOOK
RECEIVER
1) Unsnap to Re
m
ove Both Plastic Pieces Above Connector Panel
Mic
Hole
PIN
PIN
2) Place Power Adapter in to Power Adapter Holder
2a) Insert Power & Ethernet Cables Through An
y
Desired Conduit
4) Place PINS onto Hook Receiver on Backbox
4a) At the Sa
m
e Ti
m
e, Place the Ca
m
era onto Foa
m
Holder
2b) Connect Cables (Power, Ethernet, USB, etc.) to Connector Panel
Cover Hole with Provided
Torx Button Socket Cap Screw &
T15 Torx Driver Bit
3) Connect the USB - A to B Cable:
HOOK
RECEIVER
4b) Place Foot Stand onto Power Adapter Holder
USB-B to USB to Analog Audio Module (UAAM), USB-A to Phone
5) Connect Wires fro
m
Ar
m
ored Cord Handset &
Hookswitch to Ter
m
inal Block on UAAM
BACKBOX
6a) Lift Foot Stand Upward with Left Hand,
6b) Grasp the Upper Right Corner of the Phone with Right Hand
Still Connected.
Ca
m
era
Foa
m
Holder
Hole Plug
Faceplate
Re
m
ove Phone fro
m
Backbox Slowl
y
Because Cables are
Cutout, Conduit Hole Ø 1.16 [Ø29.5] Fits 1" EMT Fittings
Speaker
Hole Cluster
11/32" or 9
mm
Socket & Socket Wrench
Tool Required to Re
m
ove Hole Plug:
KO
KO
Power Plug
DX70
(Custo
m
er Provided)
KO
Open Ca
m
era Shutter
1) Use Clean Da
m
p Cloth to Wipe Surface Clean
Screen Cleaning Instruction:
KO
Place
Here
Power Suppl
y
Power Cable
to AC Outlet
Phone Mounting Instruction:
Power Cord
Through Slot
Plexiglass Cleaning Instruction:
Plexiglass Cleaner to Wipe Surface Clean
Use Provided Securit
y
Torx
Driver Bit to Fasten Screws to Backbox
Tool Required:
Electric Hand Drill or
Powered Screwdriver
2) Screw Driver
1) Ha
mm
er
Tool Required to Re
m
ove Knock Outs (KO):
3) Plier
Self-Tapping Screw, Stud Anchors or
Fits up to 1/4" [10
mm
] Square Neck Carriage Bolt,
Knock Outs (KO) & Ke
y
holes:
Machine Screw
USB-B
Plug
Use Provided Securit
y
Torx
Driver Bit to Fasten Cover Screw
to Faceplate
Note #1
(See Note #1)
Power Adapter
Holder
USB-A
Plug
Power Adapter
(See Figure #3)
Figure #2 (See Also Figure #5)
Figure #3
(See Figure #4)
Figure #4
(See Figure #2)
Use Provided #00 Screw Driver
to Install Wires to Ter
m
inal Block
Turn Clockwise to
Re
m
ove Phone fro
m
Backbox:
Ethernet
Foot Stand
1) Use onl
y
lint Free Microfiber Tower &
Black Wire
to Ter
m
inal
Black Wires
1
10
USB-B
Black Wire to Ter
m
inal
Green Wire to Ter
m
inal
Yellow Wire to Ter
m
inal
Red Wire to Ter
m
ianl
Ter
m
inal
Audio Module
USB to Analog
Block
Ar
m
ored Cord
Ar
m
ored Cord
Handset Retainer
Factor
y
Disconnected
to Ter
m
inal 5
Red Wire
Connections
Reconnect Before Fasten Faceplate Asse
m
bl
y
to Backbox
Connector
Receptacle
Connector
Plug
Magnetic Hookswitch
Backbox
***
***
Connections
Ar
m
ored Cord Handset
9
4
3
2
1
USB-A
Phone
Cable Connections
USB-B to USB-A
Audio Module
USB to Analog
