Installation Quick Reference
Singlewire-enabled
VoIP V2 Paging Amplifier
011085
Quick Reference
930329G
© 2011, CyberData Corporation, ALL RIGHTS RESERVED
© 2011, CyberData Corporation, ALL RIGHTS RESERVED
930329G
Quick Reference
Features
DIP Switch Settings
DIP Switches
Speaker Volume
Network Link LED (
GREEN
/
YELLOW
)
Status LED (
GREEN
)
A steady LED confirms that the Paging Amplifier is operational.
The LED will blink during a page when it is online.
Network Activity LED (
GREEN
)
Power LED (
GREEN
/
BLUE
)
The power LED is a steady
green
in low power mode and a steady
blue
during high power
mode. The power LED will only blink either during a boot up or a phone call.
RTFM Switch
To broadcast a Paging Amplifier’s current IP address, press the RTFM switch on the Paging
Amplifier for one second, and then release the switch to hear the IP address announcement.
To restore the factory defaults, complete the following steps:
1. Press and hold the
RTFM
switch for eight seconds. The Paging Amplifier will announce
the words, “restoring defaults”, and then announce the words, “rebooting”.
2. Release the
RTFM
switch. The Paging Amplifier settings
will be restored to the factory default settings.
DIP Switch Settings—Low Power—802.3af Compliant
DIP Switch
Default Setting Description
1
OFF
Sets PoE for 802.3af class.
2
N/A
Not applicable for power setting.
3
ON
Switch mode current set to
LOW
.
4
OFF
Low gain amplifier setting.
DIP Switch Settings—High Power—802.3at Compliant
a
a. If set to high power, the unit will not power ON with 802.3af compliant switch. You must use a
power injector in this mode (CyberData Part Number 011124).
High power PoE mode
conforms to IEEE 802.3at draft 3.0.
DIP Switch
Setting
Description
1
ON
Sets PoE for 802.3at class.
2
N/A
Not applicable for power setting.
3
OFF
Switch mode current set to
HIGH
.
4
ON
Force high gain amplifier.
DIP Switch 2 Settings
DIP Switch
Setting
Description
2
OFF
Manual Vol
. The speaker volume is set manually by the analog
volume trimmer.
2
ON
Bypass
. Bypasses the manual volume control of the analog volume
trimmer and uses the web page volume settings.
The CyberData Singlewire-enabled VoIP V2 Paging Amplifier provides an easy method for implementing an IP-based overhead
paging system for both new and legacy installations.
The Singlewire-enabled VoIP V2 Paging Amplifier is compatible with InformaCast Version 4.0 and higher.
Getting Started
• Download the
Singlewire-enabled VoIP V2 Paging Amplifier Operations Guide
PDF file from the Singlewire-enabled VoIP V2
Paging Amplifier product page at:
http://www.cyberdata.net/products/voip/digitalanalog/singlewirepagingampv2/docs.html
• Create a plan for the locations of your paging amplifiers.
• Prior to installation, consult local building and electrical code requirements.
Paging Amplifier Parts
Contacting CyberData
Parameter
Factory Default Setting
IP Addressing
DHCP
IP Address
a
a. Default if there is not a DHCP server present.
10.10.10.10
Web Access Username
admin
Web Access Password
admin
Subnet Mask
a
255.0.0.0
Default Gateway
a
10.0.0.1
(1) Assembly
(1) Wall Mounting Kit
(2) Plastic Ribbed Anchors
(2) #6 Sheet Metal Screws
Sales: (831) 373-2601 ext. 334
Support: 831-373-2601 ext. 333
Web:
http://www.cyberdata.net/support/contactsupportvoip.html
RMA Dept: (831) 373-2601 ext. 136
Email: [email protected]
RMA Status:
http://www.cyberdata.net/support/rmastatus.html
Warranty information is available at:
Web:
http://www.cyberdata.net/support/warranty/index.html
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: 831-373-2601
Fax: 831-373-4193
www.CyberData.net
