background image

 

10 

 
 
 
      

WARNING:

 Only use the charger 

supplied with this kit to charge the 18V Li-ion 
or optional 18V Ni-Cd batteries for this tool. 
Charging any other batteries may damage 
the charger and possibly cause serious 
injury.

 

 
Do not store or carry the battery in a manner in 
which metal objects could contact the exposed 
metal end. Do not place the battery in aprons, 
pockets, drawers, etc. with loose nails, screws, 
keys etc. The battery could short circuit causing 
a fire, personal injury or damage to the battery. 
 
Never attempt to open the battery for any 
reason. If the housing of the battery breaks or 
cracks, immediately discontinue use and do not 
recharge. 
 
Do not charge the battery if it is wet or shows 
any evidence of corrosion. 
 
A small leakage from the battery may occur 
under extreme usage, charging or temperature 
conditions. This does not indicate a failure. 
However, if the outer seal is broken and this 
leakage gets on your skin, follow these steps: 
1. 

Wash immediately with soap and water. 

2. 

Neutralize with a mild acid such as lemon 
juice or vinegar. 

3. 

If liquid gets into your eyes, flush 
immediately with clean water for a 
minimum of 10 minutes and seek medical 
attention. 

NOTE:

 The battery liquid is slightly acidic. 

 
Do not incinerate the battery. It can explode in a 
fire. 
 
Do not use an extension cord. Plug the charger 
cord directly into an electrical outlet. 
 
Use the charger only in a standard  
120V, 60 Hz electrical outlet. 

 

Do not use the charger in wet or damp 
conditions. It is intended for indoor use only. Do 
not use the charger near sinks or  
tubs. Do not immerse the charger in water. 
Do not allow the cord to hang over the edge of a 
table or counter or touch hot surfaces. 

 
 
 
The charger should be placed away from sinks 
and hot surfaces. 
 
Do not use the charger to charge any batteries 
other than the cordless drill/driver batteries. 
Other batteries may explode. 
 
Do not operate charger if the cord or plug is 
damaged. Replace the damaged cord and plug 
immediately. 
 
Do not operate the charger if it has received a 
sharp blow, been dropped or otherwise 
damaged in any way. Have a qualified 
technician examine the charger and repair it if 
necessary. Do not disassemble the charger. 
 
Do NOT charge the batteries when the work 
area or the battery temperature is at or below 0° 
C (32° F) or above  
45° C (113° F). 
 
Unplug the charger when not in use and before 
cleaning or maintenance. 
 

BATTERY PACK RECYCLING

 

 
To preserve our natural resources, please 
recycle or dispose of batteries properly. 
 
The batteries charged by this charger may 
contain chemicals and metals that are harmful 
to the environment. Never dispose of re-
chargeable batteries in your normal household 
garbage or in landfill sites as they will add to the 
pollution of the environment. 
 
Please call 1-800-822-8837 for the location of 
your nearest RBRC battery recycling location.

BATTERY & CHARGER SAFETY 

SAVE THESE INSTRUCTIONS FOR REFERENCE 

 

Содержание ConstruX
























Отзывы: