P/N IM-C35KD Rev. C
2014 Commercial Wireless Systems International, LLC.
63
6.2.6 System Test
The system test
is designed to allow testing of all installed devices without activating any NAC’s or
relay outputs. This test is commonly used for annual testing of the devices in an installation. The CP-
3500D can only be placed into test mode while the System Normal screen is showing. To enter the
test mode press the PANEL TEST button. All of the leds will flash three times then the CP-3500D will
display the test mode screen as shown below. The trouble relays will be activated and the sounder
will emit the trouble pattern while the CP-3500D is in test mode.
The devices will show on the LCD as they are activated. They will be displayed the same as if the
system was in normal operation. Alarm and Supervisory signals received while in test mode are
stored in the test log instead of the alarm and all event logs. Trouble signals are not stored in any log
while in test. The test log can be viewed after the testing is finished if necessary. The test log has a
capacity of 1000 signals. The Page Up and Page Down soft keys can be used to scroll through the
signals if desired. You can exit the test mode at any time by pressing the RESET key.
Note: The CP-
3500D will automatically exit the test mode after a 4 hour time period with no keypad buttons
pressed.
Multiple occurrences of the same type signal from any one device will only be displayed
once while in test. If you want to test the same signal from a transmitter more than once you will have
to exit and reenter test mode.
Caution: If an actual alarm is received from a device that is not
being tested, it will not activate any NAC or relay circuits. For this reason it is important to
recognize such an occurrence as this could be a real fire condition somewhere in the
installation which requires immediate attention. If this is the case you should exit the test
mode by pressing the RESET key and allow the alarm to be processed normally.
6.2.7 Event Logs
The CP-3500D has 4 alarm logs Alarm, Trouble, All Event and Test. These logs are provided for
viewing of events in chronological order as they occurred including time and date of each event. Each
log has a 1000 event limit. If the limit is exceeded the oldest event will be replaced by event 1001 and
so on. All of the logs will display events in the order of newest to oldest.
Each logs function is explained below.
1. Alarm Log
– Records all Alarm and Supervisory events while the CP-3500D is not is test
mode. This log cannot be erased. Limit is 1000 events.
1 2 : 3 3 : 2 0 P M 0 8 / 1 4 / 0 9
P a g e Up P g D o w n
P A N E L I N T E S T M O D E
A l a r m 0 4 8 1 1 d 1 1 : 5 9 : 0 0 P M 0 1 / 0 1 / 0 9
P u l l S t a t i o n E a s t S t a i r w e l l
S u p e r v i s o r y 0 2 3 a 6 2 1 2 : 0 1 : 0 4 A M 0 1 / 0 2 / 0 9
T a m p e r S w i t c h B a s e m e n t 2
T a m p e r 0 1 8 a 5 d 1 1 : 5 9 : 0 0 P M 0 1 / 0 1 / 0 9
S m o k e D e t S o u t h H a l l w a y
Содержание CP-3500D
Страница 12: ...P N IM C35KD Rev C 2014 Commercial Wireless Systems International LLC 12 Figure 1...
Страница 21: ...P N IM C35KD Rev C 2014 Commercial Wireless Systems International LLC 21 Figure 2...
Страница 47: ...P N IM C35KD Rev C 2014 Commercial Wireless Systems International LLC 47 Figure 4...
