manualshive.com logo in svg

CWSI CP-3500D, Руководство по эксплуатации и установке

Поделиться
Скачать
CWSI CP-3500D Скачать руководство пользователя страница 22

 

P/N IM-C35KD Rev. C 

 2014 Commercial Wireless Systems International, LLC. 

22 

Section 4 - System Programming 

This section details system programming options including time/date, password, base code, device 
enrollment, NAC/Auxiliary/Relay activation and resetting, tandem detector activation and deactivation, 
device editing, and zone assignment.   

  

4.1 Keypad Buttons and Menu Navigation 

 
The buttons located in the area below the LCD are used for menu navigation and data entry.  These 
include 4  Softkey, Up/Down/Left/Right, Enter and Back buttons. See figure 3 below for the location of 
these buttons. The Up/Down/Left/Right buttons are used for  menu navigation and character/number 
selection. The Enter button is for selecting and unselecting data entry fields. The Back button takes 
you one menu level back from the currently displayed menu. The softkeys are located directly under 
the LCD and are the arrowed buttons pointing up at the  LCD screen. The softkeys perform multiple 
functions  and  will  change  as  needed  for  the  particular  programming  being  performed.  The  softkey 
functions  are  displayed  on  the  highlighted  bottom  line  of  the  LCD  just  above  these  buttons.  This 
manual will refer to the softkeys as numbers 1-4 from left to right.  
 
     

 

 

 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

Figure 3  

 
 
 

 

 
 

MENU 
NAVIGATION 
BUTTONS  

SOFTKEY 

BUTTONS 

1-4 

Содержание CP-3500D
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды