Custom Audio Electronics KUBE 120 Скачать руководство пользователя страница 80

Страница: 80 / 92

11.6 Drivers installation

Embedded Web Server

To install a new driver update for the device, enter the “DRIVER” page of the “PRINTER SUPPORT” section of the embed-

ded Web Server (see the following igure).

Advanced Function

Picture Settings

Download Driver

Font Settings

Firmware Upgrade

Web Site

PRINTER SUPPORT

< Device name >

< PR

INT

DEVICE INFO │ PRINTER SETTINGS │ PRINTER SUPPORT

Download Driver

<Printer>_rel_111_Win2K_2K3_XP.exe | | Release : 1.11 | | File Size : 37 KB

<Printer>_cupsdrv-1.00.tar.gz | | Release : 1.00 | | File Size : 12 KB

You can find on this section the printer drivers.

The drivers are stored inside the printer memory: is not needed an active internet connection

Related product(s) : <PRINTER>

Category :

Drivers

Operative system(s) :

Windows 2000 / XP / Vista

Microsoft Windows GPD Driver

Related product(s) : <PRINTER>

Category :

Drivers

Operative system(s) :

Linux

CUPS (Common Unix Printer System) based printer drivers

Download file >>

Mass Storage / FTP Server

It is possible to install the new driver update directly into the folder “DRIVER” on the Flash Drive of the device.

You can enter the Flash Drive by iles sharing from Mass Storage or by iles sharing from FTP Server connection (see

par.11.1).

In both cases, the relative parameter should be enabled during the coniguration process (see chapter 5).

NOTE: To know the IP address of the device, print the Set-up report of the device (see chapter 5) or use “Locator”.
Type in the address bar “ftp://” followed by the IP address of the device.

Содержание KUBE 120





























































































Результаты поиска

Содержание KUBE 120

Отзывы:

Похожие инструкции для KUBE 120

Бренды по названию

Популярные бренды

Custom Audio Electronics KUBE 120, Руководство пользователя

Результаты поиска

Содержание KUBE 120

Отзывы:

Похожие инструкции для KUBE 120

Бренды по названию

Популярные бренды