Custom Audio Electronics KPM202 Скачать руководство пользователя страница 48

Страница: 48 / 116

6.4 Device parameters

These devices allow the coniguration of the parameters listed in the following table.

The parameters marked with the symbol

are the default values.

Settings remain active even after the device has been turned off and they are stored in non-volatile memory.

PRINTER EMULATION

Available emulations for the device:

CUSTOM/POS
SVELTA

RS232 BAUD RATE

Communication speed of the serial interface:

115200

9600

57600 4800
38400 2400
19200 1200

NOTE: Parameter valid only with serial interface.

RS232 DATA LENGTH

Number of bit used for characters encoding:

8 bits/car

7 bits/car

NOTE: Parameter valid only with serial interface.

RS232 PARITY

Bit for the parity control of the serial interface:

None

= parity bit omitted

Even

= even value for parity bit

Odd

= odd value for parity bit

NOTE: Parameter valid only with serial interface.

RS232 HANDSHAKING

Handshaking:

XON/XOFF

= software handshaking

Hardware

= hardware handshaking (CTS/RTS)

NOTE: Parameter valid only with serial interface.

BUSY CONDITION

Activation mode for Busy signal:

OffLine/ RXFull =

Busy signal is activated when the device is both in OffLine status
and the buffer is full

RXFull

Busy signal is activated when the buffer is full

NOTE: Parameter valid only with serial interface.

Содержание KPM202





















































































































Результаты поиска

Содержание KPM202

Отзывы:

Custom Audio Electronics KPM202, Руководство пользователя, Страница: 48 / 116

Результаты поиска

Содержание KPM202

Отзывы: