Curtiss-Wright EXLAR Tritex II AC Скачать руководство пользователя

Страница: 79 / 89

Curtiss-Wright | Tritex II AC 90, 115 Rev. X PN39892 7/12/22

MAINTENANCE PROCEDURES FOR RE-GREASING

Maintenance Procedure for Roller Screw Re-Greasing

If your actuator has a preloaded roller screw, do not

remove it from the cylinder. Preloaded screws require

special tooling and procedures for proper disassembly and

reassembly. Contact Exlar to arrange for maintenance of a

preloaded screw actuator.

Disassembly

Refer to the exploded view on the following page.

1.) Remove the actuator assembly from the machine by

disconnecting the cables, main rod coupling and actuator

mounting bolts or fasteners.

2.) If your unit does not have an external anti rotate assembly, skip

this step. Loosen the two machine screws that clamp the anti-

rotate cross member to the actuator output rod. Slide the anti-

rotate mechanism forward and off the actuator.

The end cap houses the Tritex drive and control. Extreme

care should be taken when removing the tie rod nuts or tie

rods so as not to twist or pull on the drive section of the actuator.

Do not disconnect the wiring between the drive and the actuator.

3.) Remove the screws holding the seal gland to the face plate. With

the screws removed, pull the seal gland off. Pry spots are

located on each side of the gland to aid in removal.

4.) When the seal gland is removed, the open end of the roller

screw internally threaded cylinder (ITC) is visible. The roller

screw can be removed by turning it counter clockwise and

threading it out of the cylinder. It may be necessary to keep the

roller screw cylinder from turning to remove the screw.

Содержание EXLAR Tritex II AC


























































































Результаты поиска

Содержание EXLAR Tritex II AC

Отзывы:

Похожие инструкции для EXLAR Tritex II AC

Бренды по названию

Популярные бренды

Curtiss-Wright EXLAR Tritex II AC, Инструкция по установке и обслуживанию

Результаты поиска

Содержание EXLAR Tritex II AC

Отзывы:

Похожие инструкции для EXLAR Tritex II AC

Бренды по названию

Популярные бренды