background image

User Manual 

– DuraNET 3300   

Connector Descriptions    

 

Page 36 of 84 

MNL-0676-01  Rev A4    

ECO- N/A 

Effective:  26 Feb 21 

 

J1 Power Connector 

Table 3.3: J1 EAU Connector Information 

 

Recept-

acle 

Used 

For 

Recept-

acle 

Label # 

# of 

Pins 

Wire 

Gauge 
(AWG) 

Panel Connector 

Part Number 

Mating Cable Connector 

Part Number 

Power 

J1 

14 

Phoenix Contact 1415337 

Phoenix Contact 1027478 
shell with 1029396 contacts 
for pins 1-4 and 1029398 
contact for pin 5 

 

 

Figure 3.3: J1 EAU Pin Arrangement

 

 

 

 

Table 3.4: J1 Connector Pinout 

 

J1 Pins 

Signal 

1, 2 

28VDC 

3,4 

28VDC RETURN 

CHASSIS GROUND 

 

Note: Phoenix Contact will not be releasing the 1027478 until sometime in Q3 2020 (delayed from Q4 
2019). For customers that must start building a power cable before the 1027478 is available, there is an 
alternate solution if the requirement is for a cable that is no more than 10 meters in length. Phoenix 
Contact makes cable assemblies with a molded connector on one end, and flying leads on the other end. 
The cable assemblies have 14 gauge wires, an overall braid shield, and a thick outer jacket. The jacket 
and the braid shield can be removed if they are not required by the application. These cables are stocked 
by a few distributors including part numbers and lengths listed in Table 3.4. 
 

Содержание DuraNET 3300





















































































Отзывы: