manualshive.com logo in svg

Cub Cadet 900 series, Профессиональное руководство по эксплуатации

На нашем сайте вы можете бесплатно загрузить инструкцию по установке для продукта Atmor 900 серии. Этот руководство поможет вам правильно установить и настроить ваш продукт для оптимального использования. Скачайте его с нашего сайта уже сегодня!

Поделиться
Скачать
background image

ELECTRICAL SYSTEM

122

4.

Battery discharge test

Occasionally a battery will discharge while sitting 
unused. To test for a battery that is “leaking” voltage:

4a.

Confirm that operator technique is not cre-
ating a situation that causes a draw.  As an 
example, if a homeowner habitually turns 
their equipment off using a safety switch 
(perhaps vacating the seat with the key 
switch still ON), that may leave a relay or 
fuel shut-off solenoid energized.

4b.

Disconnect and charge the battery fully.

4c.

Use the ammeter function of a DMM to 
check for a power draw between the nega-
tive post on the battery and the end of the 
ground cable that normally connects to it.  
There should be no significant D.C. 
Amperage flow. See Figure 7.44.

NOTE: 

A spark jumping from the post to the 

cable end is an indication that there is a substan-
tial current draw, but should not be used repeat-
edly as a diagnostic tool.  This is an extremely 
unkind thing to do to any electronic components 
of the tractor. 

4d.

Once the presence of a draw is confirmed, 
disconnect components of the system one 
at a time while monitoring an ammeter to 
see which makes the draw stop.

4e.

If the battery is being checked indepen-
dently of the equipment it powers, mea-
sure and note the battery voltage while it is 
disconnected, over a three-day period.

4f.

 There should be less than a .2 volt drop in 
the readings. If there is more than a .2 volt 
drop, the battery is bad. 

5.

Storage of batteries

5a.

Always store a battery with a full charge 
(unless the battery is a dry battery and the 
electrolyte has not been added yet). This 
may require periodic re-charging.

5b.

Take measures to prevent the battery from 
freezing in cold weather.  The electrolyte in 
a fully charged battery has a lower freezing 
point than the electrolyte in a battery with a 
lower state of charge.

5c.

Store the battery in a cool, dry place.

5d.

If storing multiple batteries (primarily store 
stock), rotate the stock so that the oldest 
battery goes out first. This will increase the 
life of the batteries.

6.

Troubleshooting

6a.

The first step in troubleshooting is to 
always verify the complaint.  Defining and 
verifying the problem reduces the possibil-
ity of misunderstanding and helps clarify 
the diagnostic approach.

6b.

The next step is to check the simple stuff 
first:

•

Check the 

fuse

 or fuses.  Some models have 

ground side fuse. Failure of any fuse is an indi-
cation that there is a problem of some sort in the 
circuit that the fuse protects.

•

Look for obvious physical damage.

•

Use the hour meter and indicator lamps as a 
guide to direct the search. As an example, when 
diagnosing a “no-crank” condition on a lawn trac-
tor with a PTO safety switch: if the PTO light is lit 
on the hour meter but the technician has visually 
verified that the PTO clutch is not engaged, the 
PTO circuit would be a reasonable place to 
check for problems. 

•

Check the battery. A valid diagnosis of many 
systems cannot be made without full system 
voltage applied.

Figure 7.44

Содержание 900 series







































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 900 series

Kärcher KM 85/50 W Bp Original Instructions Manual preview
KM 85/50 W Bp
Бренд: Kärcher Страницы: 336
GreenWorks Pro BL60L00 Operator'S Manual preview
BL60L00
Бренд: GreenWorks Pro Страницы: 20
Legend Brands Sahara Pro TurboDryer X4 Owner'S Manual preview
Sahara Pro TurboDryer X4
Бренд: Legend Brands Страницы: 6
Maruyama MM181 Operator'S Manual preview
MM181
Бренд: Maruyama Страницы: 24
Snapper C3203 Safety Instructions & Operator'S Manual preview
C3203
Бренд: Snapper Страницы: 14
Snapper E11306 Safety Instructions & Operator'S Manual preview
E11306
Бренд: Snapper Страницы: 24
Snapper EI5223 Parts Manual preview
EI5223
Бренд: Snapper Страницы: 24
Snapper 105287E Initial Setup Manual preview
105287E
Бренд: Snapper Страницы: 64
Snapper 1226 Operator'S Manual preview
1226
Бренд: Snapper Страницы: 78
Taski Intellibot AeroBot 1850 Quick Reference Manual preview
AeroBot 1850
Бренд: Taski Intellibot Страницы: 14
Tennant A60 Operator'S Manual preview
A60
Бренд: Tennant Страницы: 69
Best EB12 Instructions Manual preview
EB12
Бренд: Best Страницы: 20
Shark V2940C Owner'S Manual preview
V2940C
Бренд: Shark Страницы: 24
Zenoah EBZ8000/8000RH Owner'S/Operator'S Manual preview
EBZ8000/8000RH
Бренд: Zenoah Страницы: 36
ebm-papst W2S130-AA25-44 Operating Instructions Manual preview
W2S130-AA25-44
Бренд: ebm-papst Страницы: 11
Makita EB5300TH Repair Manual preview
EB5300TH
Бренд: Makita Страницы: 71
Makita DAS180Z Instruction Manual preview
DAS180Z
Бренд: Makita Страницы: 24
EINHELL 3408005 Operating Instructions Manual preview
3408005
Бренд: EINHELL Страницы: 26

Бренды по названию

Популярные бренды

Загрузить еще бренды