background image

10

4

Operating 

Your Snow 

Thrower

WARNING

Read, understand, 
and follow all instruc-
tions and warnings 
on the machine and 
in this manual before 
operating.

NOTE:  For detailed starting instructions and more 
information on all engine controls, refer to the 

Tecumseh

 Engines manual packed separately and 

Starting The Engine later in this section.

Shift Lever

The shift lever is located in the center of 
the handle panel. Place the shift lever 
into any of eight positions to control the 
direction of travel and ground speed.

Forward

Your snow thrower has six forward (F) 
speeds, with position number one (1) 
being the slowest speed. 

Reverse

Your snow thrower has two reverse (R) 
speeds, with position number one (1) 
being the slower speed.

Know Your Snow Thrower

Choke Control

The choke control 
is found on the rear 
of the engine and is 
activated by rotating the knob clockwise. Activating the 
choke control closes the choke plate on the carburetor 
and aids in starting the engine.

Throttle Control

The throttle control is located on the engine. 
It regulates the speed of the engine and 
will shut off the engine when pushed down 
completely.

Primer

Depressing the primer forces fuel directly into 
the engine’s carburetor to aid in cold-weather 
starting.

Oil Fill

Engine oil level can be checked and oil added 
through the oil fill.

Figure 4-1

34/0

For detailed starting 
instructions and 
more information on 
all engine controls, 
refer to the Tecumseh 
Engine manual 
packed separately.

Now that you have setup your snow thrower, it’s important to become acquainted with its controls and features.

Specifications are 
subject to change 
without notification 
or obligation. Images 
may not reflect your 
exact model and 
are for reference 
purposes only.

Engine Controls

Recoil Starter 

Handle

Electric Starter Outlet

Primer

Ignition 

Key

Choke 

Control

Throttle 

Control

Drive Control

Headlight

Fuel Tank

Gas Cap

Oil Fill

Chute

Assembly

Clean-Out 

Tool

Auger Control

Shift Lever

Chute Control™

Chute 

Directional 

Control

Skid Shoe

Содержание 828 SWE

































Отзывы: