CTI 2500P-J Series Скачать руководство пользователя страница 63

Страница: 63 / 82

CTI Janus Programmable Automation Controller IOG

Firmware/Configuration Update Errors

Error
Code

Description

Priority

Operation

Error Recovery

250

Front Panel SD Card

–

File

Not Found

(Could be detected by ‘SD
Card Firmware Update’ or
‘SD Card Ethernet Port
Setup’ operations)

Occurs during referenced
procedures while
controller is stopped.

Occurs when file download fails

during ‘Remote Firmware Update’

or expected file not found on SD

card during ‘Front Panel Firmware
Update’ or ‘SD Card Ethernet Port
Setup’.

Retry download, or copy

appropriate file to root directory of
SD card and insert card into front
panel holder.

260

Front Panel SD Card

–

Invalid File
(Could be

detected by ‘SD

Card Firmware Update’ or
‘SD Card Ethernet Port
Setup’ operations)

Occurs during referenced
procedures while the
controller is stopped.

Ensure appropriate file is in SD card
root directory. Check contents of

‘cti.ini’ file if error detected by ‘SD
Card Ethernet Port Setup’ utility.

Verify firmware file name (*.zip)
matches product being updated for

‘Firmware Update’.

Try using a different SD card if

performing ‘Front Panel Update’.

If condition persists, contact CTI.

Содержание 2500P-J Series



















































































Результаты поиска

Содержание 2500P-J Series

Отзывы:

Похожие инструкции для 2500P-J Series

Бренды по названию

Популярные бренды

CTI 2500P-J Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 2500P-J Series

Отзывы:

Похожие инструкции для 2500P-J Series

Бренды по названию

Популярные бренды