CTC Union FRM220A-GSW/SNMP страница 11 Скачать руководство пользователя | Manualshive

Страница: 11 / 52

background image

Chapter 1 Introduction

11

1.9 FRM220A Fault Handling

The

FRM220A

management is designed is such a way as to minimize any disruption to normal traffic in the

event of any single component failure and to allow rapid recovery of full operations through replacement of FRUs
(Field Replaceable Units).

The Power Modules support fully redundant operation. Utilizing a modular design, any mix of AC or DC power

sources may be used to supply power to the

FRM220A CH20

Chassis. Power modules are completely "Hot

Swappable". As long as one module is able to supply power, the chassis will operate non-stop. Removing any one
power module from a two module redundant chassis will not effect the operation of the entire chassis in any
manner.

All cards are designed to be "Hot Swappable". This includes any media converter cards as well as the

GSW/SNMP card itself. The following points describe what happens logically for any card fault and subsequent
replacement.

1.9.1 GSW/SNMP card Fault and Replacement

If the GSW/SNMP card should develop a fault, all media converter cards in the chassis will continue to run with

their current configuration settings, however all uplink traffic will be affected. The defective GSW/SNMP may be
pulled from the running chassis, without affecting any other media converter card. When a replacement
GSW/SNMP is inserted into the "hot" chassis, it will boot and immediately recognize that it is booting into an
already running "hot" chassis. The TCP/IP and SNMP settings will either be factory default (if the card was not
previously provisioned) or the settings will reflect previous provisioning. All provisioning settings from all the
installed media converter cards and all remote media converters will be downloaded into the new GSW/SNMP card
and saved. If any future system power off is experienced, all previous settings are restored to each media converter
card from the GSW/SNMP.

1.9.2 Media Converter card Fault and Replacement

If a media converter card develops a fault, it may immediately be replaced with a spare media converter card of

same type. The new card will be loaded with exactly the same settings as the previous card, from the provisioning
settings stored in the GSW/SNMP.

If a media converter card is replaced with a different type media converter in the same slot, the GSW/SNMP

will recognize that the card has been changed with different type converter and will upload the factory default for
that card.

«
...
9
10
11
12
13
...
»

Содержание FRM220A-GSW/SNMP





















































Отзывы:

Нет отзывов

Похожие инструкции для FRM220A-GSW/SNMP

TNS5500D Series

Бренд: 3onedata Страницы: 5

IPS7112G-4GS-8GPOE

Бренд: 3onedata Страницы: 3

Бренд: KELCO Страницы: 2

Бренд: Zektor Страницы: 17

Бренд: Black Box Страницы: 26

Бренд: Edge-Core Страницы: 9

Бренд: Black Box Страницы: 28

Бренд: Zamel Страницы: 2

EXT-UHDA-HBTL-RX

Бренд: Gefen Страницы: 33

Бренд: Nextech Страницы: 4

Бренд: Linkskey Страницы: 2

Бренд: Larson Electronics Страницы: 2

ControlZAPP CZ CESR 10VDC

Бренд: DANLERS Страницы: 2

Бренд: Voith Страницы: 98

IMI Sensors 691A80

Бренд: PCB Piezotronics Страницы: 15

Бренд: PS Engineering Страницы: 32

Бренд: Efapel Страницы: 44

Бренд: Datavideo Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды