manualshive.com logo in svg

CS-Lab SimDrive M4-H040K, Руководство пользователя

Поделиться
Скачать
CS-Lab SimDrive M4-H040K Скачать руководство пользователя страница 4

 

1.

 

Introduction 

1.1

 

Signs used in this guide 

 

 __________________________________________________________________________________ 

 Potential danger and/or possible injury risk 

 __________________________________________________________________________________ 

 Useful information, tips 

 __________________________________________________________________________________ 

 Warning, failure to comply with these warnings may lead to inappropriate functioning or 
damage of the device 

 __________________________________________________________________________________ 
 

1.2

 

Standards compliance 

simDrive™ servo drives were designed and made in accordance with the national and international 
standards for industrial control systems based on electronic components: 

 

EN 61800-5-1 

Adjustable speed electrical power drive systems -  Safety 

requirements - Electrical, thermal and energy 

EN 61800-3 

Adjustable speed electrical power drives  systems. EMC 

requirements and specific test methods 

EN 61000-6-2 

Electromagnetic compatibility (EMC). Generic standards –  

Immunity for industrial environments  

EN 61000-6-4 

Electromagnetic compatibility (EMC). Generic standards - 

Emission standard for industrial environments 

EN 61000-3-2 

Electromagnetic compatibility (EMC). Limits for harmonic 

current emissions  

EN 61000-3-3 

Electromagnetic compatibility (EMC). Limitation of voltage 

changes, voltage fluctuations and flicker in public low-

voltage supply systems,  

 

The product was 

made in lead-free technology

, RoHS compliant. 

 

 

 

 

 
 
 

 

The  simDrive™  servo drive  is a high-voltage device that can be hazardous to your health and life 

Before you start any installation turn off the power of the device and wait min.  10 minutes – it is 
the time needed to discharge a capacitor.

 

 

4 

simDrive™ - AC Servo Drive User Guide 

Содержание SimDrive M4-H040K



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды