Crystal Vision Indigo ViViD 3G Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 47

Crystal Vision Indigo ViViD 3G Скачать руководство пользователя страница 10

Crystal Vision

Rear modules and signal I/O

3 Rear modules and signal I/O

The 2U Indigo 2 frame will house up to 12 single height modules and dual power supplies.
The 1U Indigo 1 frame will house six single height modules and a single or dual power supply.
The Indigo DT desk top boxes have a built-in power supply and will house up to two single
height modules. All modules can be plugged in and removed while the frame is powered
without damage.

Note: For details of fitting rear connectors please refer to the appropriate frame manual.

The ViViD 3G range can support the following rear modules: RM41, RM57 and RM67.

Rear module connections with RM41

The RM41 being a single height module will allow maximum packing density with one HD/SD
video input and four HD/SD video outputs. The RM41 when used with ViViD 3GS and 3GS-20
(bottom picture) has an additional SYNC input for the synchroniser reference.

RM41 rear module connector

Description

RM41

•

12 per Indigo 2 frame

•

Six per Indigo 1 frame

•

Two per Indigo DT

•

All frame slots can be used

•

‘S’ models have SYNC input
for reference syncs (bottom
picture)

BNC Connections

BNC

I/O assignment

HD/SD IN

3G/High Definition/Standard Definition serial digital input.

NC or SYNC IN

Analogue Black and Burst or tri-level syncs for ‘S’ versions only.

HD/SD OUT 1

3G/High Definition/Standard Definition serial digital output.

HD/SD OUT 2

3G/High Definition/Standard Definition serial digital output.

HD/SD OUT 3

3G/High Definition/Standard Definition serial digital output.

HD/SD OUT 4

3G/High Definition/Standard Definition serial digital output.

ViViD 3G User Manual R1.4

9

19 January 2021

«
...
8
9
10
11
12
...
»

Содержание Indigo ViViD 3G
















































Отзывы:

Нет отзывов