Crystal Vision Indigo ADP 310 Скачать руководство пользователя | Manualshive

Страница: 42 / 49

background image

Crystal Vision

Appendix 1

AOP

Router

The 4x4 analogue output router allows any of the four analogue inputs to be routed
to any of the four analogue output channels. The entire router configuration can be
preset and activated with a single ‘Take’. All channels can be individually muted.
This tab only appears when a 3G-AOP2 piggyback is fitted in the rear position.

Audio OP Chs

Route the four analogue input channels to the analogue outputs.

Router

selection

buttons

Preset the router condition by selecting the button at the intersection of the input and output

channel. Input selections are labelled at the bottom and output selections on the right. The

button will light dark red once selected and red once taken. N.B. GUI example shows the four

input channels routed to the four output channels one-to-one. Input front 3G-AIP2 C1 is

preset to be routed to output Ch 12.

Take

Select this to action all presets. N.B. Dark red preset selections will light red once taken.

Present

LEDs always on for analogue inputs.

Embed Mute

For all four analogue output channels.

Output channels C9-C12

Select to mute analogue output channel.

ADP 310 User Manual R1.2

41

19 June 2019

«
...
40
41
42
43
44
...
»

Содержание Indigo ADP 310


















































Отзывы:

Нет отзывов

Похожие инструкции для Indigo ADP 310

Бренд: National Instruments Страницы: 85

Бренд: Tektronix Страницы: 178

Бренд: Alarm Страницы: 5

Disc Publisher XR

Бренд: Primera Страницы: 2

Бренд: Commell Страницы: 36

HFisolator 9730/26-11

Бренд: Stahl Страницы: 2

UST510-52B-FL Series

Бренд: AXIOMTEK Страницы: 77

Бренд: Smacq Technologies Страницы: 22

Бренд: Multi-Link Страницы: 31

Бренд: MicroNova Страницы: 113

Бренд: Fast Страницы: 66

Бренд: Alpine Страницы: 17

Бренд: MA Страницы: 4

Бренд: NAUTICAST Страницы: 20

Бренд: SeaLevel Страницы: 19

Y.FORCE YTPC400

Бренд: YTTEK Страницы: 26

PMP/PTP 450 Series

Бренд: Cambium Networks Страницы: 155

Бренд: Edimax Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды