Crystal Vision Indigo ADP 310 Скачать руководство пользователя | Manualshive

Страница: 35 / 49

background image

Crystal Vision

Appendix 1

9 Appendix 1

Statesman

In July 2014, Statesman control of ADP 310 was superceded by VisionWeb
control. Statesman is no longer supported after this date, but information for
existing users is included in this appendix.

Introduction

The Crystal Vision Statesman PC control software is designed to control a range of
Crystal Vision modules via Ethernet control from a PC. Statesman provides a user
friendly means of configuring and operating Crystal Vision modules with the benefit of
“see-at-a-glance” status monitoring.

The main Statesman application communicates with each module in a frame through
a Statesman-capable front panel CPU or full active control panel. Either of these must
be fitted to allow Statesman control.

Statesman operation

The initial view will show an Explorer style view of the connected frames and
modules. Double clicking on a module will enable the display of the main application
menus.

The two large control panes shown in the upper and lower halves of the window may
display different menus for the same card, or controls for different cards. Click on the
horizontal button-bar between the two panes to close the lower pane or drag the
button to vary the size of the panes.

ADP 310 User Manual R1.2

34

19 June 2019

«
...
33
34
35
36
37
...
»

Содержание Indigo ADP 310


















































Отзывы:

Нет отзывов

Похожие инструкции для Indigo ADP 310

Бренд: GE Страницы: 4

Бренд: NAIM Страницы: 2

Бренд: SurfControl Страницы: 2

Бренд: Pressalit Care Страницы: 31

Бренд: TRENDnet Страницы: 12

Bluespoon 17-1000

Бренд: Radio Shack Страницы: 1

Бренд: Idis Страницы: 16

Бренд: ZIMO Страницы: 13

Бренд: Juniper Страницы: 420

Slideaway CL1008

Бренд: ATEN Страницы: 77

Бренд: Keysight Technologies Страницы: 106

airPoint Nexus sB3210

Бренд: SmartBridges Страницы: 55

Бренд: Robotis Страницы: 10

Бренд: StetSom Страницы: 18

Analog Pulse Generator 812-OP/H

Бренд: Link electronics Страницы: 2

Бренд: Fujitsu Страницы: 20

Бренд: Fujitsu Страницы: 49

Бренд: Fujitsu Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды