background image

INITIAL PAIRING TO THE VOICE PROMPTS:
1. READY (POWER ON)
2. SEARCHING PHONES (FOR PREVIOUS PAIRED PHONES)
3. PLEASE SEARCH AND SELECT THE “BEEBG-25” DEVICE FROM 
    MOBILE PHONE AND ENTER “0000”.
4. YOU ARE NOW READY TO USE THE HF SYSTEM.
Note: The Bluetooth interface will remember up to the last 8 devices.

Note: If pairing is unsuccessful after several attempts power off then 
power back on to re-attempt, if unsuccessful please contact our tech 
support line. 

AUTO RE-CONNECT:
1. The BEEBG-25 module will automatically re-connect the a previously 
   paired mobile phone when the ignition is turned “ON” to the vehicle
   and the mobile phone’s Bluetooth feature is also on.

Note: The Bluetooth module will re-connect with the last mobile phone’s 
it was paired with. If no mobile phone is not found, it will 
revert to the pairing process.

BLUETOOTH INTERFACE FOR SELECT 2006-2011 GM LAN 11 BIT VEHICLES

CHEVROLET
2007-2010 Cobalt
2006-2011 HHR
2008-2011 Malibu

PONTIAC
2007-2010 G5
2007-2010 G6
2006-2009 Solstice

SATURN
2006-2009 Aura
2006-2010 Sky

We recommend reading this installation guide first before starting any 
work.  Following these instructions from “Start” to” Finish” will ensure 
a smooth and hassle free installation. We offer telephone support M-F 
9:00 AM – 5:00PM PDT at 1 (888) 607-4449. We are here to help.

PRELIMINARY:
- Disconnect the po) battery cable for radios that are 
  non-navigation. Radios that are navigation ready should not 
   disconnect the battery cable. Please use caution when installing. 
   Do not install the interface near or on the vehicle’s HVAC system. 
   This will prevent overheating and condensation build up.
- Determine the proper installation method for your specific vehicle.
   Use overview to help you determine installation method.

INSTALLATION
1. Remove the factory radio to gain access to the factory radio wiring 
    connectors.
2. Disconnect the factory connectors from the rear of the factory radio.   
3. Connect the male connectors of the interface power harness into the 
    factory radio.
4. Reconnect the factory connectors into the mating connectors of the 
    interface harness.
5. Connect the male 3-pin connector into the pigtail connector.
6. Route the microphone to a desired location, (for example near the 
    rear view mirror).
7. Re-install a factory radio back into the vehicle’s dash.

All features of this module may vary by mobile phone 
manufacturer. For questions on your mobile phone’s 
features, please reference the mobile phone’s user manual 
for information.

OPERATING THE HANDS-FREE FEATURES ON THE RADIO

UNABLE TO CONTROL THE BT FUNCTIONS ON RADIO

BEEBG-25

VOICE DIAL   

     PRESS TALK BUTTON ONCE

ANSWER 

 

     PRESS TALK BUTTON ONCE

END A CALL  

     PRESS SEEK DN BUTTON ONCE

REJECT 

 

     PRESS SEEK DN BUTTON ONCE

ANSWER SECOND CALL       PRESS SEEK UP BUTTON ONCE
SWITCH BETWEEN CALLS    PRESS SEEK UP BUTTON ONCE
INCREASE VOLUME 

     PRESS VOLUME UP ONCE

DECREASE VOLUME 

     PRESS VOLUME DN ONCE

PRIVACY MODE 

     PRESS SEEK UP ONCE

USING THE STEERING WHEEL CONTROL BUTTONS

Note:  If an incoming call is answered from the mobile phone’s keypad, 
the call will direct itself to the headset on the mobile phone. To re-direct 
the phone call to the “BEEBG-25”, it must be done directly from the 
mobile phone.

Note: When transferring a phone call to the mobile phone for privacy,
the user must re-connect the BEEBG-25 and the mobile phone by 
selecting the module from the device menu on the phone. 
Note: If after ending a call the radio is powered “OFF”, you must power 
“ON” the radio to regain volume control.

FAV     MENU 

EQ        CAT 

BAND

SEEK

SEEK

EJECT

LOAD

REV

FWD

CD/

AUX

i

3-PIN

(male plug)

TO FACTORY

RADIO

14-PIN

(male plug)

16-PIN

(male plug)

14-PIN

(male plug)

16-PIN

(male plug)

TO FACTORY
HARNESS

24-PIN

(male plug)

12-PIN

(male plug)

3-PIN

(male plug)

TO FACTORY

RADIO

24-PIN

(male plug)

24-PIN

(female plug)

TO FACTORY
HARNESS

24-PIN

(male plug)

12-PIN

(male plug)

14 AND 16-PIN CONNECTORS:

24-PIN BLUE CONNECTOR:

MIC

BALL JOINT

MOUNTING THE MICROPHONE
1. Insert the mounting clip into the ball joint on the microphone.
2. Mount the clip on your visor or near the rear view mirror.
3. Route the remaining cable along the edge of the roof liner and 
    towards the back of the radio, hiding the cable from sight.

MIC

BALL JOINT

END

ANSWER

VOL  +

VOL  -

TALK BUTTON

Note: Premium Audio Systems and BOSE Systems need to “Turn On” 
the radio for hands-free audio to be heard.

APPLICATIONS

Отзывы: