manualshive.com logo in svg

Crusader CWS5-031, Руководство пользователя

Поделиться
Скачать
Crusader CWS5-031 Скачать руководство пользователя страница 6

6 | 

P a g e

 

 

Assembly 

Step  1:

  Unpack  the  system  and  ensure  all  the  components  are  included  with  the  system.  Your 

system is shipped with the following components: 

System Sizing

 

All Crusader UV systems are rated for a specific flow rate under specific water quality parameters. 
The equipment has been designed to ensure that the appropriate dose will be delivered provided 
all parameters are followed. 

PLEASE NOTE

 that the flow rate for each system can be higher or lower 

than  what  the  system  is  rated  for  however  this  will  change  the  dose  level  that  the  system  will 
deliver.  A  lower  flow  is  not  a  concern  as  the  dose  will  increase  however  a  higher  flow  rate  will 
decrease the dose and therefore compromise the microorganism inactivation. 

It is important to know the maximum flow rate that your water system delivers.  If you do not have 
this information you can simply fill a 1 gallon bucket with water and time how long it takes to fill up. 
This will be the maximum flow rate for the home.  Choose a Crusader system that is suitable.   

PLEASE NOTE:

  It is always better to oversize your system then to undersize. For example, if your 

pump delivers 8 gpm it is recommended to install any of the Crusader 10 gpm systems. There will 
come a time where your home is using water at the pump’s maximum capacity. 

 

Содержание CWS5-031



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды