Crown CT26010HX, Оригинальное руководство пользователя

Страница: 27 / 180

27
English
base plate 14, make sure that the teeth of the base
plate gear wheel fall into the hollows on the power
tool body.
• Close the latch
15
, as shown in figure 2.3.
Assembling / dismantling of dust extractor con-
necting adaptor (see fig. 3)
• Install the dust extractor connecting adaptor 21 on
the base plate 14 , as shown in figure 3. Make sure that
latch of the dust extractor connecting adaptor 21 fall into
the hollow of the base plate 14 �
• Lock the position of adaptor
21
, screwing in the set
screw 20 (see fig. 3).
• Connect a vacuum cleaner that can remove dust
generated by the material to be processed to the dust
extractor connecting adaptor
21
(use a suitable adapt-
er, if necessary)�
• Disassembly operations do in reverse sequence�
Installation / adjustment / dismantling of the guide
with a roller (see fig. 4-5)
The guide 19 is used for milling edges with router bits
which do not have support bearings at the end�
• Install the guide 19 on the base plate 14 and fix it
with the setscrew 17 (see fig. 4).
• You can adjust a vertical position of the guide 19
depending on the router bit used and the thickness of
the workpiece (see fig. 5.1):
• loose the setscrew 17 ;
• move the guide 19 up or down;
• tighten the setscrew 17 �
• You can adjust a horizontal position of the guide
19
to
define the thickness of material removal (see fig. 5.2):
• loose the fixing screw 27 ;
• rotate the lead screw 28 to move the holder 29
to set the thickness of material removal (distance
"a");
• tighten the fixing screw 27 �
• Disassembly operations do in reverse sequence�
Installation / adjustment / dismantling of the paral-
lel guide (see fig. 6-7)
Parallel guide 18 enables milling along the straight
line side surface of the workpiece�
• Install the holder 31 on the base plate 14 and secure
it with the setscrew 17 (see fig. 6.1).
• Assemble parallel guide 18 as shown in figure 6.2.
• You can adjust the offset from the workpiece edge:
• loose the wing nut 35 (see fig. 7.1);
• move the guide 34 to set the offset from the
workpiece edge (see fig. 7.2);
• tighten the wing nut
35
(see fig. 7.1).
• Disassembly operations do in reverse sequence�
Charging procedure of the power tool
battery
Initial operating of the power tool
The power tool is supplied with a partially charged
battery 8. Before the first use, the battery 8 must
be fully charged.
Charging process (see fig. 8)
• Press the battery lock 9 and remove the battery 8
(see fig. 8.1).
• Connect the charger 24 to the power supply�
• Insert battery 8 into charger 24 (see fig. 8.2).
• Disconnect the charger 24 from power supply after
charging�
• Remove the battery 8 from the charger 24 and
mount battery 8 in the power tool (see fig. 8.3).
Charger indicators (see fig. 8)
Charger indicators 36 and 37 inform of the battery 8
charging process� Signals of the indicators 36 and 37
are shown on the label 38 (see fig. 8).
• Fig� 8�4 - (the green indicator 36 is on, the battery 8
is not inserted in the charger 24 ) - the charger 24 is
connected to the power network (ready for charging)�
• Fig� 8�5 - (the green indicator 36 is blinking, the bat-
tery 8 is inserted in the charger 24 ) - the battery 8 is
being charged�
• Fig� 8�6 - (the green indicator 36 is on, the battery 8
is inserted in the charger 24 ) - the battery 8 is fully
charged�
• Fig� 8�7 - (the red indicator 37 is on, the battery 8 is
inserted in the charger 24 ) - the charging process of
the battery 8 is terminated due to inappropriate tem-
perature� When the temperature conditions are nor-
mal, the process of charging will resume�
• Fig� 8�8 - (the red indicator 37 is blinking, the bat-
tery 8 is inserted in the charger 24 ) - the charging pro-
cess of the battery 8 is terminated because of its failure�
Replace the faulty battery 8 , its further use is prohibited�
In the process of charging the battery 8
and the charger 24 become hot, it is a
normal process.
Switching the power tool on / off
Stand-by mode
To switch on the power tool, you must first switch
on stand-by mode.
Switching on stand-by mode:
Press and release button 4 - the power tools turns
into stand-by mode (LED lamp 12 will be lit)� You
can switch the power tool on or off by pressing the
on / off switch 3 � If the power tool is in standby mode
for 20 seconds and the on / off switch 3 has not been
pressed, the power tool switches off automatically to
save energy (LED lamp 12 goes out)�
Switching off stand-by mode:
Press and release button 4 - the stand-by mode will be
switched off (LED lamp 12 will be not lit)� Now you can
not switch on the power tool�
Switching on:
You must first switch on stand-by mode as
described above. Press and release on / off switch 3
(router bit will start to rotate)�
Switching off:
Press and release on / off switch 3 (router bit will be
stop) or press and release button 4 (power tool will be
switched off completely)�