Crow Shepherd Скачать руководство пользователя страница 34

Страница: 34 / 73

thecrowgroup.com

Page | 33

Radio Zones

Parameter

Description

Default Configuration

Name

Enter name to identify the Zone

Zone #

Add Zone (Learn Radio

zone)

Radio detector must be enrolled into the panel before it can

be used.

Select zone # , Add Zone -> Link Type :ISM or DECT , Device’s

ID, Device type

Note

The pairing of DECT ULE device must be preliminarily

performed from "Communication"

→

"DECT"

→

"Learn DECT

Device".

When the DECT device pairing is done, then you can go to

"Radio Zones" and assign the DECT device ID to a zone.

Delete radio zone

Removing radio zone from the system.

Zone Config

This function set remotely the radio zone parameters such as

led on/off, pulse detection, Pet immunity, Gain level, etc.

Dedicated menu

according to detector

type enrolled

Radio Zone Module

Select device type “ ISM “ for RF devices or “DECT” for DECT

devices.

Zone Configuration –features & options examples:

Detector

PIR

Wireless

Available Options
LED(s) state

: Activation or not of the LED indicators

Supervision

: Time period between each supervision in minute (from 1 to 30)

Pet Immunity

: Activation of up to 25Kg Pet immunity

Number of Pulses

: Pulse count for each motion detection

Sensitivity

: PIR Sensitivity

MAG

Wireless Door / Window Magnet

Available Options
LED Enable

: Activation or not of the LED indicators

Содержание Shepherd










































































Результаты поиска

Содержание Shepherd

Отзывы:

Похожие инструкции для Shepherd

Бренды по названию

Популярные бренды

Crow Shepherd, Руководство по установке

Результаты поиска

Содержание Shepherd

Отзывы:

Похожие инструкции для Shepherd

Бренды по названию

Популярные бренды