If the hood and trunk zone, or optional sensor circuit is bypassed when
the system is armed, instead of the normal arming confirmation the siren
will chirp four times and the parking lights will flash four times to alert you.
However, if a door zone is bypassed, the siren and light confirmation will
be the normal two chirps and flashes, as many vehicles are equipped with a
delayed interior light illumination. In these vehicles, the interior light delay
would typically cause the system to indicate a bypass if the system is armed
during the delay. In these cases, the arming indication is normal, and the
door zone is protected by the system five seconds after the interior light
turns off.
LAST DOOR ARMING BY EXITING THE CAR
Last Door Arming
:
Last Door Arming is a programmable feature which configures the system
to arm itself without needing a command from the transmitter. This conve-
nient feature offers a high level of security and may entitle the vehicle owner
to an insurance discount since the user does not need to remember to arm
the system each time the vehicle is exited. The Last Door Arming feature
may be coupled, if desired, with the automatic locking of the vehicle’s doors
when the system arms itself.
Page 6
The Last Door Arming process:
✓
When the vehicle’s ignition has been turned off, the system waits until a
door is opened. When the door is closed, or when the last door is closed
when more than one door is opened, the siren will chirp twice, the park-
ing lights will flash twice, and the Status Light will begin flashing
rapidly. The Last Door Arming countdown has begun.
✓
Thirty seconds later the siren will again chirp twice, the parking lights
will again flash twice, the starter interrupt will engage, and the Status
Light will begin flashing slowly. If connected and programmed to do so,
the vehicle’s doors will also lock. Three seconds after these actions oc-
cur, the system is fully armed.
Notes
:
•
If a door is reopened during the thirty second period between the first
and second set of double chirps, the countdown will stop and reset. When
the reopened door is closed again, the 30 second countdown starts over
Page 27
The remaining transmitter operations are very similar- silent arm and disarming
is still operated by pressing and releasing twice the same button used for Auxiliary
Channel #2, and the sensor can still be bypassed, but pressing and releasing the
Auxiliary Channel #3 button after arming the system. Driver Door Priority
Unlocking is also available; for 5 seconds after disarming pressing the arm/disarm
button again will produce the system output necessary for all doors unlock, but after
the 5 second period the operation reverts back to arming the system on the next button
press. Remote Panic is also still operable, but it is not the “enhanced”, always
unlocking the doors.
When programming this feature, press the Upper Left “Lock” Button to config-
ure the system as “1 Button” arm/disarm operation; or press the Upper right “Unlock”
Button for “2 Button” operation.
Extra, replacement, or optional transmitters are available from your Crime Guard
dealer, or visit www.caralarm.com on the Internet for ordering information
This feature operates regardless of the previous feature’s “Steady Siren” or “Pulsed
Horn” setting. All four transmitter buttons are used to program the four different
levels, as shown below with the system’s response also noted. While programming
this feature, the buttons can be repeatedly and sequentially pressed, thus making it
easy to choose the setting with the most desirable chirp volume.
Feature #20 1 Or 2 Button Arming / Disarming
(Factory Default
Setting 2 Button Operation)
Part #
119-05B
or
119-05R
Part #
144-05B
or
144-05G
Pressing & releasing this button
alternates arming & disarming
Pressing & holding this button
operates Auxiliary Channel #2
Pressing & holding this button
operates Auxiliary Channel #3
Optional 3-button transmitter
Standard 4-button transmitter
*
“
:
” button not used
:
*
This feature is used for special applications, and dramatically changes how the
transmitter operates the system. In the factory default setting of “2 Button”
operation, one transmitter button will arm the system only; and a second button will
disarm the system only. If this feature is changed to the “1 Button” setting, a single
transmitter button will alternate, or “toggle”, the arming and disarming of the system
with every press of the button. This booklet thoroughly and exclusively describes
the “2 Button” operation; the following illustration shows the basic “1 Button”
operations for the standard 4-button transmitter and for an optional 3-button
transmitter.
