Feature #5 Ignition Activated Override
Factory Default Setting
Off (
press
“disarm/unlock” button to program
)
Option:
On (
press
“arm/lock” button to program
)
This feature allows an activated system to be overridden and disarmed by simply
turning th
e i
gnition switch on within 10 seconds of the system’s activation. After
10 seconds, the Emergency Override must be performed or the transmitter “dis-
arm/unlock” button can be used to disarm the system.
Feature #6 Doors Lock With Ignition On
Factory Default Setting
On (
press
“arm/lock” button to program
)
Option:
Off (
press
“disarm/unlock” button to program
)
This feature configures the system to automatically lock the vehicle’s doors every
time that the ignition switch is turned on. An exception to this would be if feature
#8 is turned on, and a door being open when the ignition switch is turned on. The
following feature #7 controls the automatic unlocking operations, and feature #8
provides for an override of this automatic locking if a door is open when the ignition
is turned on.
Feature #7 Doors Unlock With Ignition Off
Factory Default Setting
On (all doors will unlock)*
(
press
“
III
” button to program
)
Options:
Off
(
press
“arm/lock” button to program
)
Driver’s Door Only*
(
press
“disarm/unlock” button to program
)
All Doors Except Driver’s Door*
(
press
“
II
” button to program
)
Similar to the previous locking feature, except this feature controls the unlock
operations when the ignition is turned off, and it has more options because of the
650i
5
’s multiple unlocking outputs.
*Multiple unlock outputs offer the capability of unlocking only the driver’s
door when the system is disarmed (Driver Door Priority Unlocking), and then the
option of unlocking all doors with a second press of the “disarm/unlock” button.
The driver’s door unlocking differently from the other doors must be config-
ured when the system is installed!
If the system is installed without the Driver’s Door Priority Unlocking
interface, this feature unlocks all of the doors when the ignition switch is turned off.
If Driver’s Door Priority Unlocking is installed, this feature can control only the
driver’s door unlocking when the ignition is turned, all doors unlocking, or all doors
except the driver’s. The following feature provides for an override of this automatic
unlocking if a door is open when the ignition is turned off.
Page - 24
Page - 9
While the System is Armed, and should it Trigger
While the security system is armed, this is indicated by a slowly flashing Status
Light. Should any intrusion attempt be detected, the system will instantly activate,
or "trigger". Once triggered, the Crime Guard loudly sounds the siren and flashes
the parking and interior lights on and off.
When it is first triggered, the Status Light changes its flash pattern, and the doors
will automatically relock. Should a door be open when the system triggers, it will
wait until the door is closed, and at that time relock the doors. The automatic
relocking of the doors denies access to the thief, and is just one of the many exclusive
patented features of the Crime Guard. The siren will sound and the parking and
interior lights will flash for 30 seconds unless you disarm the system first (60, 90
and 120 seconds activated periods are options- see Feature #11, page 26). If all
protected entries are secure at the end of the 30 seconds, the system will stop and
rearm itself, ready to detect further entry attempts. If there is a protected entry still
open or the impact sensor still in a violated state at the end of 30 seconds, the system
will reactivate for two more 30 second cycles. In this case the system will stop after
a total of 3 cycles and rearm automatically, and then ignore only the open entry or
violated sensor. When the entry is closed or the sensor is reset, protection will begin
instantly for the formerly affected circuit.
When triggered, the alarm condition can be stopped instantly with the transmitter.
Which transmitter button pressed to stop it it has these effects upon the system:
• Pressing “arm/lock” will rearm the system, stopping both system’s alarm
condition (leaving it armed).
• Pressing “disarm/unlock” will disarm the system, leaving the doors locked,
stopping both system’s alarm condition (leaving it disarmed). Pressing this
button a second time unlocks the doors.
Anytime that the security system triggers, the Status Light will indicate which
protected zone triggered the system by flashing two (hood/trunk), three (door) or
four (sensor) times between pauses. This “Zone Violation” code will continue to
flash, even after disarming. The system can hold two different violation codes in it's
memory, which is cleared by turning the ignition switch "on". Once the Crime
Guard has been activated and reset, the disarming confirmation changes to make the
user aware that it was activated.
Prewarning Detection Circuit:
When the sensor is triggered by a light
impact or shock to the vehicle, the security system will respond by chirping the siren
3 times and locking the doors. After this Prewarning circuit has been triggered five
times it will automatically shutdown until the alarm system is disarmed, then armed.
