Page 23
Feature #2
SecureCode Programming Mode
(Factory Default Setting: 1 Press)
SecureCode is a unique patented feature which allows you to custom
select the number of Valet Switch presses which would be required in order
to perform an Emergency Override. Instead of “1 press” of the Valet Switch,
a customized programming of the SecureCode would require from 2 to 12
presses. If any of the three Vehicle Recovery features are utilized, a
customized SecureCode would require that the correct SecurCode entry of
Valet Switch be made to cancel the Vehicle Recovery activation.
The “as received” factory default setting of “1 press” is the most
convenient, as an Emergency Override will occur instantly when the Valet
Switch is pressed, but it is not as secure as a customized setting. When a
customized SecureCode has been programmed, the system will disarm a few
seconds after the correct entry.
To custom program a new SecureCode:
Follow Steps 1 to 4 on page 20; at Step 4 the Valet Switch will be pressed
and released two times. The system’s response will be two siren chirps, and
the Status Light flashing twice, pausing, then repeating. Within 10 seconds,
press and release the transmitter’s Large Upper Button; the siren will chirp
twice to confirm system is ready to accept the new SecureCode entry. Now
press and release the Valet Switch the desired number of times. The
SecureCode can be programmed for 1 to 12 presses, but the entry must be
made within 5 seconds. Wait for the siren to chirp the same number of times
as the Valet Switch presses to confirm the new SecureCode entry.
Important:
If no additional features need to be programmed, exit Programming
Mode by allowing the 10 second time limit to expire without any further
programming activity. Do not exit Programming Mode by turning on the
ignition switch.
Feature #3
Chirp Confirmation
(Factory Default Setting On)
This feature allows the permanent removal of the system’s chirping the
siren as a audible confirmation when performing functions such as Arming
and Disarming. Please note that utilizing this feature to remove the
confirmation chirps does not affect siren chirping operations associated
with the ATV Warning, sensor prewarning or Programming Mode.
Page 24
Changing the Chirp Confirmation:
Follow Steps 1 to 4 on page 20; at Step 4 the Valet Switch will be pressed
and released three times. The system’s response will be three siren chirps,
and the Status Light flashing three times, pausing, then repeating. Within 10
seconds, press and release the transmitter’s Large Upper Button to turn the
Chirp Confirmation on (the siren will chirp once) or the Small Lower Button
to turn the Chirp Confirmation off (the siren will chirp twice).
Feature #4
30 or 60 Second Alarm Duration
(Factory Default Setting 30 Seconds)
This feature allows the option of a 30 or 60 second Alarm Duration,
which is when the system has activated in Armed state, sounding the siren
and flashing the parking lights.
Changing the Alarm Duration:
Follow Steps 1 to 4 on page 20; at Step 4 the Valet Switch will be pressed
and released four times. The system’s response will be four siren chirps, and
the Status Light flashing four times, pausing, then repeating. Within 10
seconds, press and release the transmitter’s Large Upper Button to set the
Alarm Duration for 30 seconds (the siren will chirp once) or the Small Lower
Button to set the Alarm Duration for 60 seconds (the siren will chirp twice).
Feature #5
Automatic Sensor Zone Bypass
(Factory Default Setting On)
This feature configures the system to automatically bypass the sensor
protection zone if the sensor should be triggered five times during a single
Armed state. If the sensor is bypassed, it will be reinstated the next time the
system becomes Armed.
Programming Automatic Sensor Zone Bypass:
Follow Steps 1 to 4 on page 20; at Step 4 the Valet Switch will be pressed
and released five times. The system’s response will be five siren chirps, and
the Status Light flashing five times, pausing, then repeating. Within 10
seconds, press and release the transmitter’s Large Upper Button to turn the
Automatic Sensor Zone Bypass feature on (the siren will chirp once) or the
Small Lower Button to turn this feature off (the siren will chirp twice).
