DO
GUIDE
DO
Program the Device
Program the Device via USB
1. Perform any necessary programming using the COMPUTER (USB) connection prior to attaching the front panel of the MP-B10/MP-B20 to the
device.
NOTE
: Programming can also be performed via the LAN port.
2. Use the four included 4-40 x 1/2" screws and the included 1/16" Allen wrench to attach the front panel to the MP-B10/MP-B20.
MP-B10/MP-B20
Media Presentation Button Panel
DO
Install the Device
Install the Device into an Electrical Box
After the facility control network has been installed and verified, use the
following procedure to install the MP-B10/MP-B20 into a standard 3-gang
electrical box:
1. Turn the system power OFF.
2. Use the four included 6-32 x 3/4" screws to attach the mounting plate
to the electrical box.
3. Attach the mounting plate ground wire to an earth ground.
NOTE
: Ensure that the unit is properly grounded.
Install the Cables
Route all appropriate cables through the electrical box, and then attach
them to the rear of the MP-B10/MP-B20.
When making connections to the MP-B10/MP-B20, note the following:
• Use Crestron
®
power supplies for Crestron equipment.
• Apply power after all connections to the device have been made.
WARNING
: Incorrect wiring may damage the MP-B10/MP-B20.
Complete the Assembly
Use the two included 4-40 x 1/4" screws to attach the MP-B10/MP-B20 to
the mounting plate.
CAUTION
: Excess wire that is pinched between the MP-B10/MP-B20 and
the electrical box could short out. Ensure that all excess wire is completely
contained inside the electrical box and not between the box and the
device.
Label the Buttons
1. Attach the three label holders by placing them over their respective
slots and by sliding them downward into position.
2. Attach the included labels in the appropriate positions on the
MP-B10/MP-B20.
3. Optional custom-engraved labels for the MP-B10/MP-B20 can be
ordered separately by downloading the Crestron Engraver software
from
www.crestron.com/software
.
DO
Check the Box
QUANTITY
PRODUCT
COLOR
PART NUMBER
1
Plate, Mounting
4506280
2
Screw, 4-40 x 1/4", Pan Head, Phillips
2007156
4
Screw, 6-32 x 3/4", Truss Head, Combo
2009211
1
Tool, 1/16" Allen Wrench, L-shape, 3" Blade
2022867
MP-B10-W, MP-B20-W Only
1
Labels, Sources, 100 Piece Set
White
4509400
1
Labels, Actions, 100 Piece Set
White
4509402
4
Screw, 4-40 x 1/2", Button Head, Hex
2021396
MP-B10-B-T, MP-B20-B-T
1
Labels, Sources, 100 Piece Set
Black
4509401
1
Labels, Actions, 100 Piece Set
Black
4509403
4
Screw, 4-40 x 1/2", Button Head, Hex
Black
2021395
MP-B10-W Only
1
Front Panel and Label, 10 Button
White
4506186
MP-B10-B-T Only
1
Front Panel and Label, 10 Button
Black
4506187
MP-B20-W Only
1
Front Panel and Label, 20 Button
White
4506182
MP-B20-B-T Only
1
Front Panel and Label, 20 Button
Black
4506183
Ground
wire
Mounting
plate
Screws
(4): 6-32 x 3/4"
NET:
To any Cresnet
®
network device
LAN:
10/100Base-T Ethernet to
LAN or web
LAN PoE
NET
Screws (2): 4-40 x 1/4"
Button
label
Label
holders (3)
Computer
(behind front cover):
To USB computer
console port
MP-B20
Screws (4): 4-40 x 1/2"