background image

Essence™ In-Wall Speakers

quickstart guide 

IW5, IW6, IW8

www.crestron.com

888.273.7876

201.767.3400

Specifications subject to 

change without notice.

IW5, IW6, IW8

Mount/Remove Speakers

The in-wall speakers include six toggle clamps that simplify the mounting process. If the 

grilles are mounted on the speakers, remove them before proceeding. (Refer to “Install/ 

Remove Grilles”, below.)
1.  Connect the speaker cable wires to the spring terminals by pressing the top of the 

terminals down and inserting the exposed strands into the hole. Make sure that the 

+

 wires go to the 

+

 (red coded) terminals, and the 

 wires go to the 

 

(black coded) 

terminals. 

2.  With the toggle clamps turned inward, insert the speaker into the opening. As the six 

screws on the front of the speaker are tightened, the toggle clamps first rotate into 

clamping position (refer to the figure to the right) and then begin holding the speaker 

to the wall. Tighten the screws until the speaker is secured; do not overtighten.

3.  Speaker removal is accomplished by reversing the procedures given in steps 1 and 2 

above.

 

a.  Loosen the front screws to unclamp the speaker. Continue to loosen the screws 

until the toggle clamps rotate inward.

 

b.  When the speaker is loose, carefully remove it from the opening.

 

c.  Disconnect the wires from the terminals.

Install/Remove Grilles

The zero-bezel frameless grilles are held in place by powerful magnets. To remove the 

grilles, grip the edges and pull away from the speaker.

1

1

Installation

The product of expert Crestron

®

 audio engineering, 

Essence™ speakers deliver the pinnacle of performance 

for demanding residential installations. Select esoteric 

materials, top shelf components and a refined, high-end 

appearance underscore the meticulous design behind 

each model. The result is a complete line of in-wall and 

in-ceiling speakers worthy of a place in every room of 

the finest custom home.

QUICKSTART DOC. 7394B (2034614)    12.12

Determine Placement In Room

Rear View (Typical)

Install Cables

Run the cables from the audio source to each speaker location following all appropriate 

local codes. Strip the ends of the speaker cable wires 1/4” to 1/2” (6 mm to 12 mm) and 

twist the exposed strands.

Spring 

Terminals (2)

Toggle 

Clamps (6)

Tighten 

Screws

The Essence line promises the ultimate in installed audio 

design, delivering simply stunning sound quality while 

minimizing any impact on your décor thanks to paintable 

zero-bezel grilles. 

Speaker placement is largely a matter of personal preference. However, placing the speaker 

near a corner will extend its low frequency response.

Prepare Mounting Holes

Before finalizing the speaker location, check to make sure there are no fixtures, pipes, air 

ducts, joists, or other possible obstructions. Use a good quality stud finder to locate joists.

If there is no access to the area behind the wall, and it is uncertain that there are no 

obstructions, carefully drill a small hole just through the wall near the middle of the proposed 

speaker location(s) and use one of the commercially available inspection devices designed for 

this purpose, or do one of the following:

●  Use a piece of stiff wire, bent into an “L” shape, wit

h one end long enough to explore an 

area equal to the size of the speaker with the toggle clamps extended. Insert the wire into 

the hole, make sure it rotates freely in a complete circle and that there is sufficient depth, 

or

●  Use a drywall saw to cu

t  a small hole at a 45° angle toward the inside of the hole. An 

angle cut simplifies repair since the removed piece can be reinserted to help plug the hole. 

90°

If there are no obstructions, use the supplied template to trace outlines of the mounting holes 

on the wall. Cut the final mounting holes at a 90° angle to the wall.

Paint the Speaker Grilles

Speaker grille painting should be done prior to mounting. 
1.  Carefully remove the material on the underside of the grilles and set them aside for 

reinstallation. It may be necessary to use a knife or other sharp instrument to free 

an edge of the material so it can be peeled away. Use care to avoid cutting or 

tearing the material.

2.  Dry brush or lightly spray the surface to be painted. Use care to avoid clogging the 

holes in the grilles.

3.  Once the paint is dry, reinstall the material to the underside.

Front View (Typical)

45°

Отзывы: