Crestron IV-SAM-VXN-1B Скачать руководство пользователя страница 73

Страница: 73 / 108

Product Manual — Doc. 9324C

IV-SAM-VXN-1B, IV-SAM-VXP-1B, and IV-SAM-VXS-1B • 68

System Configuration

The Automate VX system can be configured using its web configuration interface as described in
the sections that follow.

NOTE: Most system configuration can be accomplished by using the

Intelligent Video Room

Designer tool

. This tool is available on the Crestron website and locally on the Automate

VX system. For more information on using the tool, refer to

Room Designer on page 26

Access the Web Configuration Interface

To access the web configuration interface for the Automate VX system, open the Chrome®
browser on the Automate VX system. The web configuration interface loads automatically.

To access the web configuration interface from a different device:

1. Enter the IP address of the Automate VX system with port 3579 appended to the address

(for example, "10.1.10.31:3579")

A login page is displayed.

2. Enter the following login credentials:

username: admin

password: 1beyond

3. Select Login.

Содержание IV-SAM-VXN-1B













































































































Результаты поиска

Содержание IV-SAM-VXN-1B

Отзывы:

Похожие инструкции для IV-SAM-VXN-1B

Бренды по названию

Популярные бренды

Crestron IV-SAM-VXN-1B, Руководство по эксплуатации продукта

Результаты поиска

Содержание IV-SAM-VXN-1B

Отзывы:

Похожие инструкции для IV-SAM-VXN-1B

Бренды по названию

Популярные бренды