Crestron iLux CLS-C6 Скачать руководство пользователя страница 43

Страница: 43 / 92

Crestron

CLS-C6/C6M & CLSI-C6/C6M

iLux Integrated Lighting System

Operations Guide – DOC. 6347E

iLux Integrated Lighting System: CLS-C6/C6M & CLSI-C6/C6M

•

To exit

Lights

mode, press the

Lights

button again (or press

Cancel

), and the LED

goes off. The unit returns to

Standard

mode. (Also, if no adjustments are made

within 1 minute, the unit reverts to

Standard

mode.)

Pressing the

Shades

button automatically exits

Lights

mode and enters

Shades

mode.

Shades Mode

Shades

mode allows manual control any of the six shade groups.

To enter

Shades

mode, raise the cover and press the

Shades

button. The

corresponding LED lights, and now the six function buttons can be used to adjust

shade groups 1 through 6. Any scenes that are currently in the middle of a fade

immediately goes to their target value. The seven white front panel LEDs go out. In

this mode, these LEDs do not reflect the feedback status of the associated scenes.

When the unit is returned to

Standard

mode, these LEDs return to their standard

feedback indication.

•

The six function buttons act as open/stop/close/stop (rocker type) for each

of the corresponding six shade groups.

•

Operation is as described for the Shade Control button type in

Standard

mode (page 33.)

•

For shade groups with C2N-SSC-2 controllers:

⇒

While in

Shades

mode, the bar graphs indicate the current shade

position.

⇒

The two-digit display indicates the current percentage level of the

shade group being adjusted (CL, 01 to 99, OP).

⇒

The two-digit display disappears (goes blank) 3 seconds after the shade

stops moving (due to either a stop command or reaching a limit of

travel).

NOTE:

The two-digit display only shows the shade level when being

adjusted from front panel buttons in

Shades

mode or scene

programming. It does not display when adjusting levels from a remote

panel or Cresnet.

•

For shade groups with C2N-SDC or C2N-SDC-DC controllers:

⇒

Bar graphs initially display nothing while a shade is not moving. While

the shade is moving open, the bar graph LEDs scroll in an upward

direction. While moving closed, the bar graph LEDs scroll in a

downward direction. When the shade is stopped or the maximum time

is reached, the bar graph turns off.

⇒

The two-digit display shows “OP” or “CL” accordingly.

⇒

The up/down button acts as a shades master when in

Shades

mode, no

matter what function is programmed for it. Pressing the top while the

shade is stopped sends it to full open; pressing the bottom while the

shade is stopped sends it to full close; pressing anything while the

shade is moving stops it. Pressing both while the shade is stopped

causes the shade to move in the opposite direction.

⇒

The ON and OFF buttons on the CLS-C6 unit itself operates normally

while in

Shades

mode. The same is true for all scene recall or scene

toggle functions triggered by remote panel or Cresnet command.

⇒

Inputs/commands from any remote devices, motion detector, and

Cresnet control system are processed as usual while in Shades mode. If

they affect the group (or groups) being adjusted, the manual adjustment

Содержание iLux CLS-C6





























































































Результаты поиска

Содержание iLux CLS-C6

Отзывы:

Crestron iLux CLS-C6, Руководство по эксплуатации, Страница: 43 / 92

Результаты поиска

Содержание iLux CLS-C6

Отзывы: