The Crestron® FT2A-CP series connector plates offer an
interface solution for use with the FT2-ELEC series FlipTop™
system. Each connector plate installs in a single module
slot within the FlipTop to provide connectivity for AV
sources and mobile devices (i.e., laptops, tablets, etc.) using
separate interface cables (not included).
NOTE:
The FT2A-CP series connector plates are active
modules and therefore only compatible with the FT2-ELEC
series FlipTops. The modules are not compatible with the
FT2-MECH series FlipTops.
Check the Box
Item
Qty
FT2A-CP-RJ45, FT2A-CP-AUD-RCA2,
FT2A-CP-4K-HD, FT2A-CP-4K-DP, FT2A-CP-VGA,
FT2A-CP-AUD or FT2A-CP-VID-RCA1
1
Overview
Crestron offers several models of connector plates,
including DisplayPort™ and HDMI® modules that are
capable of passing video signals up to 4K60 4:4:4 and have a
minimum bandwidth of 18 Gbps. Additional models support
VGA, stereo audio, composite video, and Ethernet. A backlit
LED permits the user to identify a connection at the table.
Each LED features an international symbol indicating the
connection type and lights when the module connects to a
FlipTop power bus.
FT2A-CP Modules
LED icon
Port type
FT2A-CP-4K-DP
FT2A-CP-VGA
FT2A-CP-4K-HD
FT2A-CP-AUD
FT2A-CP-AUD-RCA2
FT2A-CP-VID-RCA1
FT2A-CP-RJ45
Each FT2A-CP module is 0.98 in. x 1.97 in.
(25mm x 50 mm) and requires one empty module slot in the
FlipTop for installation.
Install the Module
NOTE:
The FT2A-CP module is only compatible with the
FT2-ELEC series FlipTops.
Install the FT2A-CP module into the FlipTop assembly. If the
bezel and locking bars have not been installed on the FT2
FlipTop assembly, skip to step 4.
1.
Tap the lid retraction button to retract the one-touch
lid, which disappears into the FT2 FlipTop assembly. If
the assembly has two lids, open both.
2.
Remove and retain the magnetic bezel from the FT2
FlipTop assembly by grasping the inside of the bezel
and firmly pulling it up and away from the assembly
until the magnetic hold is broken.
3.
Using a manual torque screwdriver, unscrew, remove,
and retain the two locking bars on either side of
the module row where the module is to be installed.
For example, if installing the FT2-CP module in the
bottom row of a FlipTop, remove the middle and
bottom locking bars.
Locking Bar Location
Locking bars (3)
4.
Orient the connector plate so that the module’s LED
icon is facing toward the front of the FlipTop assembly
as shown in the next column. Connect the cable to the
bottom of the module and feed it through the empty
module slot.
Positioning the FT2A-CP Module (FT2A-CP-4K-HD shown)
FT2A-CP-4K-HD
Retractable lid
(located in rear
of assembly)
Front of
FlipTop
assembly
LED Icon
5.
Push the top of the module down so it slides into the
appropriate module slot in the FlipTop assembly. Use
the guide ribs on the front and rear of each module to
help position the module in the assembly.
Installing the FT2A-CP-4K-HD into the FlipTop Assembly -
Overhead View
FT2A-CP-4K-HD
FT2A-CP Series
Connector Plates for FT2-ELEC Series FlipTops™
