CEN-GW1 and CENI-GW1
Universal Wireless Gateway, ER Wireless, SG Wireless, and infiNET EX® Wireless Gateway
Product Information - 8859A
(2056509)
06.21
Getting Started
Scan the QR code to view the Quick Start Guide.
www.crestron.com/docs/8860
For additional information on the Crestron® CEN-GW1, visit
www.crestron.com/model/6511027.
For additional information on the Crestron® CENI-GW1, visit
www.crestron.com/model/6511029.
RF Gateway Important Notice
Do not install this Crestron® gateway within 15 feet (4.6 meters) of
other SG (Sub Ghz) gateways, infiNET EX® gateways, Crestron ER
gateways, or Wi-Fi® access points.
Certification and Compliance
Regulatory Model: M201913001
IMPORTANT NOTE: To comply with ISED CANADA and FCC RF
exposure compliance requirements, the antenna used for this
transmitter must be installed to provide a separation distance of at
least 20 cm from all persons and must not be co-located or operating
in conjunction with any other antenna or transmitter.
REMARQUE IMPORTANTE: Pour être conforme aux exigences de
conformité d’ISED CANADA et de la FCC en matière d’exposition aux
radiofréquences, l’antenne utilisée pour cet émetteur doit être
installée de manière à assurer une distance de séparation d’au moins
20 cm de toutes les personnes toute autre antenne ou émetteur.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is
subject to the following conditions:
(1) This device may not cause harmful interference and (2) this device
must accept any interference received, including interference that
may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
l
Reorient or relocate the receiving antenna.
l
Increase the separation between the equipment and receiver.
l
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
l
Consult the dealer or an experienced radio/TV technician for help.
Please note that any modifications to the device software or
configuration, including but not limited to the init file(s), can cause
device performance to vary beyond the scope of the currently
referenced FCC authorization. Accordingly, if any user modifications
are sought to be made to the device software or configuration, the
user may be required to independently seek fresh FCC and other
regulatory authorizations as relevant prior to distributing or
marketing the devices or products incorporating the same.
Industry Canada (IC) Compliance Statement
CAN ICES-3 (B)/NMB-3(B)
This device contains licence-exempt transmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions:
1.
This device may not cause interference.
2.
This device must accept any interference, including interference
that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent
appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils radio
exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
1.
L’appareil ne doit pas produire de brouillage;
2.
L’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le
fonctionnement.
As of the date of manufacture, the product has been tested and
found to comply with specifications for CE marking.
The Waste Electrical & Electronic Equipment (WEEE) directive
marking on a product indicates that it should not be disposed of with
general waste. Instead, you are encouraged to reuse or recycle the
product in accordance with Directive 2012/19/EU of the European
Union. Proper disposal of this product will help prevent potential
negative effects on the environment and human health, which could
otherwise be caused by inappropriate waste handling. Penalties may
be applicable for incorrect disposal of this waste, in accordance with
your national legislation. For information about recycling this
product, please contact your household waste disposal service, your
original distributor, or Crestron.
