Crane NRI Currenza C2 Скачать руководство пользователя страница 76

Страница: 76 / 83

National Rejectors, Inc. GmbH, Buxtehude

aTch

confiGuraTion

Configuration

Batch configuration

If the same settings are to be made for several coin changers of the same

series, it is sufficient to

configure one changer as required,

save this state of settings in the HENRI setting module and then

transmit the state of settings from HENRI into the remaining changers

to be configured

Only the data that applies to the coin changer will be stored and transmitted

but not the data saved in the coin validator or peripheral equipment. The

following settings remain unaffected and may need to be adapted in

addition:

Coin and currency data

•

Acceptance bands and coin values

•

Please note that, whenever you are copying coin changer data

from older devices with a smaller range of functions and load

this data into a new device, the new functions may need to be

adapted, if necessary. In the opposite case, an older device will

also not be provided with the additional functions of the new

device.

Configuring coin changer master

If you haven’t done so already, first of all you have to configure a coin

changer so that its configuration can be used as clone for the other coin

changers to be configured (see Chap. 3 "Presettings" to Chap. 10 "Basic

settings").

Содержание NRI Currenza C2




















































































Результаты поиска

Содержание NRI Currenza C2

Отзывы:

Crane NRI Currenza C2, Техническая документация инструкция, Страница: 76 / 83

Результаты поиска

Содержание NRI Currenza C2

Отзывы: