Crane Crown B12 Series страница 31 Скачать руководство пользователя | Manualshive

Страница: 31 / 32

background image

Submersible Pumps

Resistance of cable and pump motor (measured at pump control):
Red-Black:_______Ohms(

Ω

) Red-White:_______Ohms(

Ω

) White-Black:_______Ohms(

Ω

)

Resistance of Ground Circuit between Control Panel and outside of pump: __________Ohms(

Ω

)

MEG Ohms check of insulation:
Red to Ground: _________ White to Ground: __________ Black to Ground: ____________

Operational Checks

Is there noise or vibration present?   YES___ NO___  Source of noise/vibration: ___________
Does check valve operate properly?   YES___ NO___ N/A___
Is system free of leaks?   YES___ NO___

Leaks at: ______________________________

Does system appear to operate at design fl ow rate?   YES___ NO___
Nominal Voltage: _____________________ Phase: 1Ø 3Ø (select one)
Voltage Reading at panel connection, Pump OFF: L1, L2  _____   L2, L3 ____   L1, L3 _____
Voltage Reading at panel connection, Pump ON: L1, L2  ______  L2, L3 ____   L1, L3 _____
Amperage Draw, Pump ON:   L1 ____________

L2 _____________

L3 _____________

Submersible Pumps

Are BAF and guide rails level / plumb?   YES___ NO___
Is pump seated on discharge properly?   YES___ NO___
Are level controls installed away from turbulence?   YES___ NO___
Is level control operating properly?   YES___ NO___

Is pump fully submerged during operation? YES___ NO___

Follow up/Corrective Action Required

YES___ NO___

Additional Comments:

____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________

Startup performed by: _____________________ Date: ______________________________

Present at Start-Up

( ) Engineer: ____________________________ ( ) Operator: ________________________

( ) Contactor: ____________________________ ( ) Other: ___________________________

All parties should retain a copy of this report for future trouble shooting/reference

A Crane Co. Company

420 Third Street

83 West Drive, Brampton

Piqua, Ohio 45356

Ontario, Canada L6T 2J6

Phone: (937) 778-8947

Phone: (905) 457-6223

Fax: (937) 773-7157

Fax: (905) 457-2650

www.cranepumps.com

«
...
29
30
31
32
»

Содержание Crown B12 Series

































Отзывы:

Нет отзывов

Похожие инструкции для Crown B12 Series

Clima Canal JDPC.002

Бренд: Jaga Страницы: 8

Бренд: SAB Страницы: 7

Бренд: SAER Elettropompe Страницы: 76

aroSTOR VWL B 200/5 UK

Бренд: Vaillant Страницы: 24

Бренд: Vaillant Страницы: 20

Бренд: Vaillant Страницы: 24

Бренд: Walrus Страницы: 6

Бренд: Walrus Страницы: 4

Aquarea WH-ADC0309J3E5B

Бренд: Panasonic Страницы: 40

Бренд: Calpeda Страницы: 43

Бренд: Wacker Neuson Страницы: 52

Бренд: Annovi Reverberi Страницы: 100

Scalekleen EV9796-01

Бренд: Everpure Страницы: 2

Бренд: HARNITEK Страницы: 28

Бренд: EBARA Страницы: 40

FLOW-PRO 350MOP

Бренд: EUROM Страницы: 32

Бренд: Heraeus Страницы: 28

Бренд: Lochinvar Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды