manualshive.com logo in svg

Crane Barnes EcoTRAN, Руководство по установке и эксплуатации, Страница: 31 / 35

Поделиться
Скачать
Crane Barnes EcoTRAN Скачать руководство пользователя страница 31

31

Appendix 5: OPTIONAL FLAT COVER INSTALLATION

STEP 1: ADAPTER INSTALLATION

A.  With the riser attached to the basin, make sure the basin tank assembly is in place and stable in the hole. The hole  

 

should not be completely backfilled.

B.  Make sure the riser is cut to the proper length per the hole depth (See STEP 6 on page 12).

C.  Push the adapter onto the riser making sure the station power cable and conduit is positioned correctly for wiring  

 

back to the control panel.

D.  In order to determine correct engagement of the adapter onto the riser, press the adapter onto the riser until the  

 

J-hook in the adapter comes into contact with the riser per Section View below.

E.  Install the six retaining fasteners supplied. The fasteners should fall inside the riser valley per Section View below.

STEP 2: FLOOD PLAIN VENT (Supplied by others)

A.  Insert male threaded 1¼” pipe coupling adapter into vent port.

B.  Plumb as required per Local Codes. Use thread sealant compatible    

 

with plastic threads in the adapter vent port. Thread 1¼” locknut onto   

 

male NPT side adapter.

STEP 3: POSITIONING/ENGAGING FLAT COVER

A.  Remove flat cover assembly from common parts box.

B.  Remove all small parts shipped loose inside the flat cover adapter and  

 

place them into the common parts box.

C.  Orient cover over adapter, lining up the bolt holes. 

D.  Place washers on all six, 3/8-16, 1.25” screws and   

 

 

  tighten screws into cover until tight.

STEP 4: OPTIONAL NON-FLOOD PLAIN 

VENT INSTALLATION

A.  Tighten 2” PVC Nipple into Bug Free Vent.  

 

Tighten opposite end of 2” PVC Nipple    

 

into central threaded flange in Flat Cover   

 Assembly.

Содержание Barnes EcoTRAN




































Отзывы:

Нет отзывов