background image

18

It is advisable that all three phase control panels be 
purchased from the factory.

SECTION: C START-UP OPERATION

C-1) Check Voltage and Phase:

Before operating pump, compare the voltage and phase 
information stamped on the pump’s identifi cation plate to the 
available power.

C-2) Check Pump Rotation:

Before putting pump into service for the fi rst time, the motor 
rotation must be checked. Improper motor rotation can result 
in poor pump performance and can damage the motor and/
or pump. To check the rotation, suspend the pump freely, 
momentarily apply power and observe the “kickback”. 
“Kickback” should always be in a counter-clockwise direction 
as viewed from the top of the pump motor housing and will 
always be in the opposite direction of the rotation arrows 
cast in the pump volute.

C-2.1) Incorrect Rotation for Three-Phase Pumps:

In the event that the rotation is incorrect for a three-phase 
installation, interchange any two power cable leads at 
the control box. Recheck the “kickback” rotation again by 
momentarily applying power.

C-2.2) Test Procedure For Moisture Sensor Control:

With a moisture detection control, a normally closed push 
button and neon indicating lamp is typically provided as a 
means of checking the moisture sensing components. When 
the push button is depressed, the indicating lamp will be 
illuminated to indicate (A) power is supplied to the control, 
(B) the control is operative, and (C) wiring to the moisture 
sensing probes in the motor is intact. This procedure should 
be performed periodically to confi rm integrity of the circuit.

C-3) Start-Up Report:

Included at the end of this manual is one start-up report 
sheet, this sheet is to be completed as applicable. Return 
a copy to Barnes and store the second in the control panel 
or with the pump manual. It is important to record this data 
at initial start-up since it will be useful to refer to should 
servicing the pump be required in the future.

C-3.1) Identifi cation Plate:

Record the numbers from the pump’s identifi cation plate on 
the START-UP REPORT provided at the end of the manual 
for future reference.

FIGURE 5

Содержание 6SHMJ150N6

















































Отзывы: