Crane 3SHM, Инструкция по установке и эксплуатации

Страница: 6 / 48

6
DISCHARGE ......................
3”, 125 lb. Horizontal Flange
Slotted to accomodate 80mm
ISO Flanges
LIQUID TEMPERATURE ...
104°F (40°C) Continuous
VOLUTE .............................
Cast Iron ASTM A-48, Class 30
WEAR RING ........................ C954 Lead-Free Bronze
MOTOR HOUSING ............. Cast Iron ASTM A-48, Class 30
SEAL PLATE ...................... Cast Iron ASTM A-48, Class 30
IMPELLER:
Design .................... Enclosed Monovane, With Pump
Out Vanes on Back Side.
Dynamically Balanced ISO G6.3
Material ................. Ductile Iron ASTM A-536, 65-45-12
SHAFT ............................... 416 Stainless Steel
“O” RINGS .......................... Buna-N
HARDWARE ....................... 300 Series Stainless Steel
LIFTING BAIL ..................... 300 Series Stainless Steel
PAINT ............................... Epoxy Dupont Corlar
®
Amine
Epoxy, Two Coats
SEAL: Design ................... Tandem Mechanical, Oil Filled
Reservoir.
Material: Inboard .... Rotating Face - Carbon
Stationary Face - Ceramic
Material: Outboard . Rotating Face - Silicon Carbide
Stationary Face - Silicon Carbide
Elastomer - Buna-N (Both Seals)
Hardware - 300 Series Stainless
(Both Seals)
CORD ENTRY ..................... Custom Molded, Quick Connected
for Sealing and Strain Relief
POWER CORD ................... CSA Certifi ed Submersible Power
Cable 2000V - Ordered Separately
SPEED ...............................
1750 RPM (Nominal)
UPPER BEARING:
Design ....................
Single Row, Ball, Oil Lubricated
Load ......................
Radial
LOWER BEARING:
Design .....................
Double Row, Ball, Oil Lubricated
Load .......................
Radial & Thrust
MOTOR: Design .................
NEMA B Three Phase Torque Curve.
Oil-Filled, Squirrel Cage Induction,
Inverter duty rated per NEMA
MG-1 part 31
Insulation ..............
Class H, Varnish & Magnet Wire
SINGLE PHASE ................ Dual voltage 208-230V 2 thru 5HP.
Requires Overload Protection to be
included in control panel.
THREE PHASE ................. Tri-voltage 208-230/460V & 575V 2
thru 5HP. Requires Overload
Protection to be included in control
panel.
MOISTURE SENSOR ....... Normally Open (N/O) with 330
K-Ohm Test Resistor Across
Probes. Requires Relay in
Control Panel
TEMPERATURE SENSOR .. Three Normally Closed (N/C).
To be wired in series with
contactor control circuit
OPTIONAL EQUIPMENT .. Seal Material, Impeller Trims,
Cord Length, Leg Kit (p/n 125506)
MARKINGS ....................... CSA, CE
WEIGHT ............................ 209 Pounds (95 Kg)
NOISE EMISSION MAX .... In-Air 65 dB-A
SUBMERGENCE .............. Max Depth 66ft (20m)
SECTION: A - PUMP SPECIFICATIONS: 3SHMP (Enclosed Monovane) Pump Models
Dimensions
inches (mm)
IMPORTANT !
1.) MOISTURE AND TEMPERATURE SENSORS MUST BE CONNECTED TO VALIDATE THE CSA LISTING.
2.) A SPECIAL MOISTURE SENSOR RELAY IS REQUIRED IN THE CONTROL PANEL FOR PROPER OPERATION OF THE MOISTURE SENSORS.
CONTACT BARNES PUMPS FOR INFORMATION CONCERNING MOISTURE SENSING RELAYS FOR CUSTOMER SUPPLIED CONTROL PANELS.
3.) THESE PUMPS ARE CSA LISTED FOR PUMPING WATER AND WASTEWATER. DO NOT USE TO PUMP FLAMMABLE LIQUIDS .
4.) INSTALLATIONS SUCH AS DECORATIVE FOUNTAINS OR WATER FEATURES PROVIDED FOR VISUAL ENJOYMENT MUST BE INSTALLED IN
ACCORDANCE WITH THE NATIONAL ELECTRIC CODE ANSI/NFPA 70 AND/OR THE AUTHORITY HAVING JURISDICTION. THIS PUMP IS NOT
INTENDED FOR USE IN SWIMMING POOLS, RECREATIONAL WATER PARKS, OR INSTALLATIONS IN WHICH HUMAN CONTACT WITH PUMPED
MEDIA IS A COMMON OCCURRENCE.
5.) THIS PUMP IS NOT APPROPRIATE FOR THOSE APPLICATIONS SPECIFIED AS CLASS 1 DIVISION 1 HAZARDOUS LOCATIONS.
29.13
(740)
3.75
(95)
14.18
(360)
11.14
(283)
6.27
(159)
Optional Leg Kit - p/n 125506