Craftsman CM2.12 Скачать руководство пользователя страница 39

Страница: 39 / 48

Problem

Probable cause

Solution

10.
Excessive fuel consumpti-
on of engine

• Poor or polluted fuel quality

• Defective injector / injection pump

• Incorrect injection moment

• Excessive wear and tear of cylinder / piston

• Insufficient supply of combustion air

• Check fuel quality. Drain fuel tank and rinse it

well. Fill with good quality fuel

• Check and replace if necessary

• Check / adjust

• Check compression, overhaul engine if

necessary

• Check the air intake and the ventilation

openings in the engine room

11.

Blue smoke coming out of
the exhaust (when idling)

• Oil level too high

• Excessive inclination angle of the engine

• Leaking oil seal of the turbo compressor

• Lower oil level

• Check / adjust alignment of engine

• Check / replace

12.

Black smoke coming out of
the exhaust (under load)

•

Defecte turbocompressor

• Insuffient supply of combustion air

• Leakage in air intake manifold

• Defective injector / injection pump

• Incorrect injection moment

• Incorrect valve clearance

• Excessive wear and tear of cylinder / piston

• Engine overheated, does not reach maximum rpm

•

Check air intake as well as the ventilation

openings in the engine room

•

Check/ replace

•

Check/ replace

•

Check and replace when necessary

• Check/readjust

• Readjust

•

Check compression, overhaul the engine if

needed.

•

Check the dimensions (diameter and pitch) of

the propeller and replace the propeller if

necessary.

13.

Engine produces white
smoke from the exhaust (at
full load)

• Air inclusion in the fuel system

• Defective injector / injection pump

• Water in the fuel system

• Defective pre-heating plugs

• Incorrect valve clearance

• Incorrect injection moment

• Poor fuel quality or polluted fuel

• Condensation of vapour in the exhaust system, on account of very low

ambient temperature

• Check / bleed the system

• Check / replace if necessary

• Check / replace water separator / fuel filter

• Check / replace

• Check / adjust

• Check fuel quality. Drain fuel tank and rinse it

well. Fill with good quality fuel

• No problem, no danger

Problems and solutions 14

craftsman marine diesel engines CM2.12 , cm2.16 / cm3.27

Содержание CM2.12

















































Результаты поиска

Содержание CM2.12

Отзывы:

Похожие инструкции для CM2.12

Бренды по названию

Популярные бренды

Craftsman CM2.12, Руководство по эксплуатации

Результаты поиска

Содержание CM2.12

Отзывы:

Похожие инструкции для CM2.12

Бренды по названию

Популярные бренды