Craftsman c950-52913-0, Руководство пользователя

Страница: 18 / 120

WARNING: Read Operator’s Manual before operating
machine. This machine can be dangerous if used
carelessly.
• Never operate the snowthrower without all guards,covers,
shields in place.
• Never direct discharge towards windows or allow
bystanders near machine while engine is running.
• Stop the engine whenever leaving the operating
position.
• Disconnect spark plug before unclogging the impeller
housing or the discharge chute and before making
repairs or adjustments.
• When leaving the machine, remove the safety key. To
reduce the risk of fire, keep the machine clean and free
from spilled gas, oil, and debris.
18
BEFORE OPERATING SNOWTHROWER
■ ■
Check the fasteners. Make sure all fasteners are tight.
■ ■
Read this OPERATOR’S MANUAL and OPERATOR SAFETY before
operating your snowthrower. Compare the illustrations with your
SNOWTHROWER to familiarize yourself with the location of var-
ious controls and adjustments. Save this manual for future refer-
ence.
NOTE: This snowthrower was shipped WITH OIL in the
engine. See “Before Starting Engine” instructions in the
OPERATION section of this manual before starting engine.
OPERATION
OPERATE THE SNOWTHROWER
The most effective use of the snowthrower will be established by experi-
ence, taking into consideration the terrain, wind conditions, and building
location which will determine the direction of the discharge chute.
NOTICE: Do not throw snow toward a building as hidden objects
could be thrown with sufficient force to cause damage.
1. Start the engine. See “To Start Engine” in this section.
2. Rotate the crank (D D, Figure 15) to set the direction (left or right) of the
discharge chute.
3. Push the deflector control lever (EE) forward or pull back to control the
angle of the chute deflector. Push the lever FORWARD to provide a
higher stream and greater distance. Or, pull the lever BACK to provide
a lower stream and less distance.
WARNING: The operation of any snowthrower can result in foreign objects being thrown into the eyes, which can result in
severe eye damage. Always wear safety glasses or eye shields before beginning snowthrower operation. We recommend
standard safety glasses or Wide Vision Safety Mask over spectacles.
CAUTION: Before operating, make sure the area in front
of the snowthrower is clear of bystanders or obstacles.
NOTE: Always release the traction control lever before moving
the speed select lever.
4. Use the speed select lever (A A, Figure 15) to select the forward drive
speed. Set the speed select lever to one of the following positions as
determined by snow conditions:
1-2 Wet, Heavy, Slushy, Extra Deep
3
Moderate
4-5 Very Light
6
Transport
NOTE: When clearing wet, heavy, snow, it is recommended that
the ground speed of the unit be reduced, maintain full throttle,
and do not attempt to clear the full width of the unit.
5. Engage the auger drive clutch lever (A A, Figure 17).
DOWN Engage Position
UP Disengage Position
6. Engage the traction drive clutch lever (B B). As the snowthrower starts to
move, maintain a firm hold on the handles and guide the snowthrower
along the cutting path. Do not attempt to push the snowthrower.
7. To stop forward motion, release the traction drive clutch lever (B B).
8. To stop the auger, release the auger drive clutch lever (A A).
9. To move the snowthrower backwards, move the speed select lever (A A, Fig-
ure 15) into first or second reverse (R1 or R2), and engage the traction drive
clutch lever (B
B, Figure 17).
Control Levers Figure 17
B
A
WARNING: Never run engine indoors or in an enclosed,
poor ventilated area. Engine exhaust contains CARBON
MONOXIDE, an ODORLESS and DEADLY GAS.
• Keep hands, feet, hair, and loose clothing away from
any moving parts on engine and snowthrower.
• Temperature of muffler and nearby areas can exceed
150°F (66°C). Avoid these areas.
• DO NOT allow children or young teenagers to operate or
be near snowthrower while it is operating.
Not
for
Reproduction