Not for
Reproduction
Protect pump from damage caused by freezing, read
operator’s manual for winter or long term storage. Freeze
damage is NOT covered under warranty.
Copyright © 2018. All rights reserved.
Every effort has been made to ensure that the information in this document is accurate and correct. However, we reserve the right to alter or otherwise improve the product and this document at any time without prior notice and without incurring obligation.
This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA) standard PW101-2010 (Testing and Rating Performance of Pressure Washers).
WARNING
Failure to read and follow the
operator’s manual and all operating
instructions before using could result in
death or serious injury.
WARNING
Risk of electrocution. Contacting
both power conductors, at the same
time could cause electric shock or burn
resulting in death or serious injury.
• Inspect cord before each use, DO NOT use if
cord is damaged.
• Keep all connections dry and off the ground.
• DO NOT touch plug with wet hands.
WARNING
High water pressure could cut
through skin resulting in serious injury.
Spray gun traps high water pressure,
even when motor is stopped and water is
disconnected. NEVER aim spray gun at people,
animals, or plants. ALWAYS point spray gun in
safe direction, press red button and squeeze
trigger to release high pressure, every time you
turn off pressure washer.
Items Included
• Main unit
• Operator’s manual
• Spray gun
• High pressure hose
• Spray wand with Quick Connect (QC)
• 7-in-1 nozzle
• Red high pressure nozzle
You will need (Not Included)
• Garden hose, 15m (50 ft.) or less
• Safety goggles (indirect vented type)
• Petroleum or synthetic grease
Unpack Electric Pressure Washer
1. Remove everything from carton.
2.
Raise handle (A) to upright position by pulling up latch (B)
on each side of handle. Push latches down to secure handle
in place.
1
3. Ensure you have all included items prior to assembly. If
items are damaged or missing, call
1-888-331-4569
.
4. Prior to assembly, lubricate rubber o-ring seals on all
connections with petroleum or synthetic grease. See
Operator’s Manual,
Lubricate O-Rings
.
2
3
4
6
7
Connect Hoses and Water Supply
1. Uncoil high pressure hose and attach black end of hose (C)
to base of spray gun (D). Tighten by hand.
2
2. Attach blue end of high pressure hose (C) to high pressure
outlet (E) on pump. Tighten by hand.
3
NOTICE
If inlet screen is damaged or missing. DO NOT use
pressure washer, call
1-888-331-4569
.
3. Before connecting garden hose (F) to water inlet (G), inspect
inlet screen (H). Clean screen if it contains debris or have it
replaced if damaged. DO NOT run pressure washer if inlet
screen is damaged.
4
4. Run cold water through garden hose (F) for 30 seconds
to clean out any debris. Connect the garden hose (not
to exceed 50 ft. (15 m) in length) to the water inlet (G).
Tighten by hand.
4
2
D
C
H
F
G
4
3
C
E
5
J
6
K
L
7
K
M
N
8
9
R
S
P
10
Connect Spray Wand and 7-in-1 Nozzle
1. Turn ON water, point gun in a safe direction, press trigger
lock button (J), then squeeze trigger to purge pump system
and spray gun of air and impurities.
5
2. Attach spray wand (K) to spray gun (L). Tighten by hand.
6
3. Pull back on collar of spray wand (K), insert 7-in-1 nozzle
(M) and release collar. Tug on 7-in-1 nozzle to make sure it
is securely in place.
7
NOTICE
For nozzle instructions, see Operator’s Manual.
NOTICE
High water supply pressure may not allow detergent to
flow. See Operator’s Manual,
Troubleshooting
.
How to Start Your Electric Pressure
Washer
1. Put on safety goggles.
2. Turn on water.
NOTICE
DO NOT run pump without water supply connected and
turned on.
NOTICE
The unit can be operated in vertical or horizontal
positions.
3. Turn master ON/OFF switch (N) to OFF (0) position.
8
4. Plug electrical power cord into a dedicated electrical circuit
rated for 120 Volts AC at 15 Amps that is properly installed
in accordance with all local codes and ordinances. Circuit is
not to supply any other electrical needs.
9
NOTICE
The indicator light must be ON for electric pressure
washer to operate.
5. Press TEST button (P). The indicator light (R) should be
OFF.
10
6. Press RESET button (S). The indicator light (R) should be
ON.
10
NOTICE
DO NOT use electric pressure washer if above test fails.
7. Turn master ON/OFF switch (N) to ON (I) position.
8
8. Point gun in a safe direction, press trigger lock button (J)
and squeeze trigger.
5
The electric pressure washer motor will start and stop as spray
gun trigger is depressed and released.
NOTICE
If a fuse blows or circuit breaker trips, motor break in
may be necessary. Run pressure washer in any PO
High Flow Mode (
) nozzle setting for 10 minutes.
How to Stop Your Electric Pressure Washer
NOTICE
To ensure detergent tank does not drain during storage,
empty after each use, see operator’s manual.
The electric pressure washer motor runs only when the trigger is
engaged. To stop the electric pressure washer and turn off the
motor:
1. Release spray gun trigger.
2. Turn master ON/OFF switch (N) to OFF (0) position.
8
NOTICE
Releasing trigger will shut off motor but does not shut
off electrical power to unit.
3. Turn off water supply.
4. ALWAYS point spray gun in a safe direction and squeeze
spray gun trigger to relieve built up pressure in unit.
NOTICE
Spray gun traps high water pressure, even when motor
is stopped and water is disconnected.
5. Disconnect GFCI plug from outlet.
9
6.
For storage instructions, see Operator’s Manual.
WARNING
Risk of electrocution. Use of an extension cord
could cause electric shock or burn resulting in death
or serious injury.
• DO NOT use an extension cord with this electric pressure
washer. Your home’s electrical circuit receptacle or extension
cord may not provide lifesaving ground-fault circuit-
interruption protection.
WARNING
Risk of electrocution. Non-operating ground fault
circuit interrupter (GFCI) could result in death or
serious injury. If indicator light does not stay on after
test and reset, do not use GFCI.
WARNING
Risk of eye injury. Spray could splash back or
propel objects resulting in serious injury. Always
wear indirect vented (chemical splash) safety goggles
marked to comply with ANSI Z87.1 when using or in
vicinity of this equipment. NEVER substitute safety glasses or
dry-condition goggles for indirect vented safety goggles.
1
B
A
B
80029109 Rev. A
Quick Setup Guide
Electric Pressure Washer
Have Questions?
Do not return to store. We can help.
Call Customer Service Toll-Free
1-888-331-4569
or visit our website,
www.Craftsman.com
