Craftex CX118 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 26

Craftex CX118 Скачать руководство пользователя страница 8

8

PROPER GROUNDING

Grounding provides a path of least
resistance for electric current to reduce the
risk of electric shock.

CX118 is for use on a normal 110 volt
circuit. Make sure that the machine is
connected to an outlet having the same
configuration as the plug. If an adaptor plug
is used, it must be attached to the metal
screw of the receptacle. To prevent
electrical hazards, have a qualified
electrician ensure that the line is properly
wired.

The band saw should be wired with a plug
having 3 prongs to fit a 3 prong grounded
receptacle as shown in figure-1. Do not
remove the grounding prong to fit it into a 2
pronged outlet.

Figure-1 110-Volts outlet for CX118

It is strongly recommended not to use
extension cords with your CX118. Always
try to position your machine close to the
power source so that you do not need to
use extension cords.

If it is necessary to use an extension cord,
make sure the extension cord does not
exceed 50-feet in length and the cord is 14-
gauge to prevent motor damage.

WARNING!

Improper connection of the equipment-
grounding conductor can result in a risk
of electric shock. Check with a qualified
electrician if you are in doubt as to
whether the outlet is properly grounded.

«
...
6
7
8
9
10
...
»

Содержание CX118



























Отзывы:

Нет отзывов