Crafco SS60-Diesel Скачать руководство пользователя страница 30

Страница: 30 / 119

Super Shot 60 Diesel Melter Part Manual

Chapter 5 Operating Instructions

………………..…………………………………..….Operating Instructions 5-6

5.4 Electric Hose Care and Cautions

Step

Action

CAUTION

Twisting and kinking of the electric hose (used on BAX, Super Shots, and EZ Series
Melters) causes the hose to fail; the electric heating wires are shorted out to the metal
hose cover and the hose stops heating.

This type of failure is not covered under the Crafco warranty.

Set the hose temperature at 193.3°C (380°F), or manufacturer recommended operating
temperature.

Allow the hose to be turned “ON” and heating for a minimum of 30 minutes.

Make sure the hose swivel between the hose and wand moves freely.

Note:

Do not twist or bend the hose over sharp edges such as the edge of the frame or

tank. Crafco, Inc. recommends you do not work directly under the boom; this may cause
damage to the hose.

Follow all machine instructions in this manual.

CAUTION

Hose damage occurs if:

The hose is bent or moved when cold.

The hose is twisted or bent at a sharp radius.

The hose is moved before being heated a minimum of 30 minutes and set at 380°F
(193.3°C).

The operator crosses over or under the hose causing the wires between the hose and
wand connection to twist or wrap up.

The swivel is cold and is not flexible which can cause the hose to twist.

The wiring between the hose and the wand is pulled, stressed, or used to support the
wand.

5.5 Storing the Electric Hose for Transport

Step

Action

Leave the hose in the boom, swing the boom clockwise towards the front of the
machine and lock the boom into position with the latch provided.

Place the wand in the wand holder and lock the wand into position with the latch
provided.

Table 5-3 Electric Hose Care

Table 5-4 Hose for Transport Instructions

Содержание SS60-Diesel




















































































































Результаты поиска

Содержание SS60-Diesel

Отзывы:

Похожие инструкции для SS60-Diesel

Бренды по названию

Популярные бренды

Crafco SS60-Diesel, Руководство пользователя

Результаты поиска

Содержание SS60-Diesel

Отзывы:

Похожие инструкции для SS60-Diesel

Бренды по названию

Популярные бренды