CR Remeha Quinta Pro 115 Скачать руководство пользователя страница 71

Страница: 71 / 92

7.4

Specific maintenance operations

If the standard inspection and maintenance operations have revealed

the necessity to carry out additional maintenance work, proceed as

follows, depending on the nature of the work:

7.4.1.

Inspection of the ignition electrode

1. Remove the ignition electrode plug from the ignition transformer.

The ignition cable is fixed to the ignition electrode and

therefore may not be removed.

2. Unscrew the 2 screws. Remove the unit.
3. Wipe off all traces of deposits using an abrasive cloth.
4. Check the ignition electrode for wear. Replace if necessary.
5. Check the gasket.
6. Refit all parts, replacing those that are damaged.

T002872-A

Quinta Pro 30 - 45 - 65 - 90 - 115

7. Checking and maintenance

250413 - 123157-03

Содержание Quinta Pro 115





























































































Результаты поиска

Содержание Quinta Pro 115

Отзывы:

Похожие инструкции для Quinta Pro 115

Бренды по названию

Популярные бренды

CR Remeha Quinta Pro 115, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Quinta Pro 115

Отзывы:

Похожие инструкции для Quinta Pro 115

Бренды по названию

Популярные бренды