CR Remeha Quinta Pro 115 Скачать руководство пользователя страница 69

Страница: 69 / 92

7.3.5.

Checking the automatic air vent

1. Switch off the boiler electrical power supply.
2. Close the gas valve on the boiler.
3. Close the main gas inlet valve.
4. Unscrew the two screws located under the front panel by a quarter

turn and remove the panel.

5. Tilt the control box forwards by opening the holding clips located

at the sides.

6. Check whether there is any water in the small hose on the

automatic air vent.

7. If any leaks are detected, replace the air vent.

7.3.6.

Checking the siphon

1. Remove the siphon and clean it.
2. Fill the siphon with water.
3. Put the siphon back in place.

R000076-B

90º

Gas/Gaz

Quinta Pro 30 - 45 - 65 - 90 - 115

7. Checking and maintenance

250413 - 123157-03

Содержание Quinta Pro 115





























































































Результаты поиска

Содержание Quinta Pro 115

Отзывы:

Похожие инструкции для Quinta Pro 115

Бренды по названию

Популярные бренды

CR Remeha Quinta Pro 115, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Quinta Pro 115

Отзывы:

Похожие инструкции для Quinta Pro 115

Бренды по названию

Популярные бренды